Produkty dla biogumy (6)

Il metano è un potente gas serra, con un potenziale di riscaldamento globale maggiore della CO2. Il metano non catturato, rilasciato in atmosfera con l’off-gas, potrebbe vanificare il contributo che la produzione di biometano può offrire alla lotta ai cambiamenti climatici. In un’ottica finalizzata a ridurre i consumi di energia e ad aumentare la sostenibilità ambientale degli impianti, la soluzione è la combustione termica rigenerativa (RTO), tecnologia caratterizzata da un’alta efficienza di abbattimento del metano e un’alta efficienza di recupero termico, che può arrivare fino al 96%; e il calore prodotto dall’ossidazione degli inquinanti, permette di azzerare il consumo di combustibile ausiliario per la maggior parte delle condizioni operative, con una riduzione dei costi operativi dell'impianto e dell’impatto ambientale. - conformità alla 2018/2001/EU RED II: efficienza di rimozione CH4 > 99% - sostenibilità del biometano - OPEX < 0,1 kWh/m3 di OFF-GAS grazie all'auto-termia

La lunga esperienza e il continuo aggiornamento permettono a Special Coverings di sviluppare prodotti all’avanguardia, come le coperture per biogas. Le coperture per biogas sono realizzate nel rispetto delle normative che regolamentano questo settore, rispondono a requisiti di sicurezza, resistenza e qualità.

The positive or negative ions fixed on these radicals are replaced by ions of the same sign in the liquid solution in contact with them.

Syntech Pavistrong A two-component coating with a modified epoxy resin base, specific for protecting concrete surfaces destined to be in contact with aggressive agents or for containing food products and drinking water. Syntech Pavistrong is certified according to EN 1504-2, for the protection of structures in reinforced concrete as well as for food contact, in accordance with the requirements of Ministerial Decree 21/03/73 and subsequent amendments. Syntech Pavistrong is characterized by its excellent chemical resistance to aggressive exposure environments, to alkalis even at high concentration, to medium concentration acids and to the flow of liquids even containing solid suspensions. It is impermeable to water and chemically aggressive agents. It constitutes an effective barrier to the penetration of carbon dioxide and the carbonation of concrete. It is non-toxic, therefore suitable for contact with food and drinking water. It has excellent adhesion to concrete, steel, bricks, stone in general and various materials commonly used in construction. The fluid consistency makes Syntech Pavistrong fast and easy to apply both by brush and roller. Industrial concrete floors. Purification tanks for waste water and related technical rooms. Food tanks, pipes and containers. Digesters and plants for the production of biogas. Coating of canalizations and liquid containment tanks. Water treatment, purification and distribution plants. Containers of acidic and basic substances. Stables, milking rooms, veterinary rooms, slaughterhouses. Analysis laboratories, warehouses, raw material storage areas and production areas. Containers for accidental spills of petroleum products, chemicals and food products. The support on which the resin system is to be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilatations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 3%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. Apply by roller, brush or spray from 150 to 200 g / m2 of Syntech Primer EP-W to consolidate the substrate and facilitate the adhesion of the subsequent coating. Apply Syntech Pavicrom when the primer is completely dry and no later than 24 hours from the end of its application. In case of presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to first apply the epoxy resin for "wet substrates" Syntech Pavidamp. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. Thoroughly mix the two components in their respective containers. Pour the can of component B into the can of component A, mix thoroughly for 2-3 minutes. To obtain a perfect mixing use a mechanical stirrer or a suitable tool. The mixture of the two components must be spread within 20-30 minutes, in order to avoid hardening in the can itself. Note that the reaction rate depends on the ambient temperature (at 30 ° C it hardens in 15 minutes). Apply on the surface to be treated, in two coats, within the indicated times, for an indicative consumption of 500-600 g / m². Do not take partial quantities from the packs to avoid any errors in the mixing ratio that would cause failure or incomplete hardening. Do not dilute the components or the mixture of the two components. From 0.50 to 0.60 kg of SYNTYECH PAVISTRONG for each square metre of surface to be covered, for two coat applications (0.25-0.30 kg per single coat). Can 2 kg [A] - Can 6 kg [A] - Can 1 kg [B] - Can 3 kg [B] - Kit: 1 Can 2 kg [A] + 1 Can 1 kg [B] - Kit: 1 Can 6 kg [A] + 1 Can 3 kg [B]

Apparecchio per eliminare gli scarti alimentari per la preparazione dei cibi .Indicato per :Ristorazione,Mense,Gradi Comunità,Hotel,Catering,Mercati Ortofrutticol

Tomato purée (or passata) is a very versatile ingredient, and one of the fundamental foods used to make many Made in Italy recipes, as well as many others, from pasta sauces to the basic condiments for pizzas, as well as being used in various meat-based main courses or vegetarian dishes. It is made exclusively from fresh tomatoes, and only high-quality, whole products are used, not waste from other processes, such as peeled tomatoes, which are instead recovered in the production of concentrates. Tomato purée can be defined as the juice or pulp of concentrated tomatoes without skin or seeds and is the result of a cold or hot extraction method whose resulting raw material is then thickened in evaporators. Carefully selecting the tomatoes used in the production of passata is crucial, as it can affect the quality and durability of the finished product. The selection criteria include ripeness and the absence of imperfections and defects. Deep red, ripe tomatoes with a higher