Produkty dla do silników (273)

Osmocem Flex A two-component osmotic cementitious waterproofing agent in water dispersion, being a modified polymer that is highly flexible and deformable, with a plastic-elastic conduct. Application by trowel, brush or roller. Ideal for waterproofing terraces, balconies and swimming pools, prior to laying the tiled or brick coating. Suitable for contact with drinking water. Osmocem Flex is certified for compatibility with contact and containment of drinking water and food substances (certificate n. 04/2010 of the Laboratorio Analysis Service di Settimo di Pescantina - VR). Two-component professional product. Proportioning of component A + component B specially designed to give the installer certainty of the result and guarantee of impeccable work: the tank of component B (8 kg) contains slightly more compared to the quantity necessary for mixing the bag (24 kg), allowing the installer, before laying the product, to withdraw from the tank up to 1 lt of the special resin of component B, dilute with 1 lt of water and use this aqueous emulsion to prime the application support; in this way at least three extraordinarily effective operations are performed with a simple and rapid priming: a) expulsion of the air from the superficial porosity _fillers (with drastic reduction of the well-known blisters that occur on low thickness elastic products); b) reduction of the support absorption (to guarantee a suitable setting of the waterproof finish); c) increase in adhesion thanks to the deep penetration of the polymeric component. Moisture-proofing concrete containment works (tubs, swimming pools, pipes, ducts, areas containing food, etc.). Moisture-proofing balconies, terraces, bathrooms, showers, etc., prior to laying successive plasters and screeds, ceramic coatings provided they are sufficiently porous and absorbent and free from any waterproofing and / or water-repellent surface treatment, whether chemical (siloxanes, epoxies, polyurethanes, etc.) or natural (wax-up). Waterproofing coating of earth-retaining masonry, micro-cracked plaster. Deformable finishing coats in general. The application surfaces must be clean, free of dirt, crumbly and inconsistent parts, dust, water-repellent treatments in general, etc., slightly roughened with a suitable preparation method (degree of roughening > 2mm, or >= 3 on the ICRI Scale - International Concrete Repair Institute). Particularly dry supports should be slightly moistened with water. It is always advisable to prime the application support with approximately 100-150 g/m2 of COMPONENT B adhesive latex in order to facilitate the expulsion of air from the surface porosity (pore stopper), reduce the absorption of the support and increase adhesion to the support. For applications on plasterboard, first apply a coat of Bond Plus as a primer. In the case of large covering surfaces on flat roofs or terraces soaked in water, it is necessary to provide suitably located steam vent "chimneys". Do not apply on supports with water leaks or any form of moving water, which must be previously blocked and remedied to prevent the product from washing away during the hardening and setting phase. Osmocem Flex comes in two predosed components that must be thoroughly mixed, with mixers with a low number of revolutions (maximum. 300 Revs/minute) until a homogeneous lump-free mixture is obtained. The addition of other ingredients should be absolutely avoided. The tank of component B (8 kg) contains slightly more compared to the quantity necessary for mixing the bag (24 kg), allowing the installer, before laying the product, to withdraw from the tank up to 1 lt of the special resin of component B, dilute with 1 lt of water and use this aqueous emulsion to prime the application support (see also the ADDITIONAL INFORMATION section). In case of exceptionally arid climate, it is possible to make moderate consistency corrections, where necessary, adding water up to a maximum of 8%. When waterproofing terraces and balconies, two coats, each about 1.5 mm thick (2.2 kg/m² per coat), of Osmocem Flex should be applied, each coat should be applied when the previous one looks stable (at least 4 hours later at 20°C). It is recommended to interpose the fibreglass alkaline-resistant mesh Armaglass 160 in the thickness of Osmocem Flex, between the first and second coat. The self-adhesive butyl band Proband should also be placed between the floor screeds and the elevation walls. Finally, it is advisable to place the special elastic band Elastotex 120 or Elastotex 120 Cloth, at any expansion joints, securing it with the same Osmocem Flex. Approximately 1.8 kg/m² of Osmocem Flex for each millimetre of thickness to be made. Packaging: Kit 24+8 kg UM: €/kg

Langjährige Erfahrung und umfangreiches Knowhow machen Codronic zum optimalen Partner im Bereich Sondermaschinenbau. Ob Medizintechnik, Verpackungstechnik, Lebensmitteltechnik, Fördertechnik oder andere Branchen – Codronic ist seit vielen Jahren zuverlässiger Partner, wenn es darum geht, erfolgreich Sondermaschinen zu entwickeln und zu konstruieren. Im Kundenauftrag entwickelt das Team von Codronic entweder einzelne Baugruppen und Komponenten oder bearbeitet Teilprojekte der Kunden in Kooperation. So können Kundenunternehmen entweder Arbeitspakete vollständig ausgliedern oder Mitarbeiter von Codronic ins eigene Team eingliedern (beispielsweise durch Remote-Arbeitsplätze).

Designing machines and devices according to client’s specification Preparation of the 3D models Preparation of the complete technical documentation