Produkty dla drewna (15)

Syntech Poliurea Primer – Epoxy SYNTECH POLIUREA PRIMER - EPOXY is a two-component primer based on modified epoxy resins and special hardeners, solvent-free. Specially formulated to provide the right compromise between impregnation and wettability of the support to which, once applied, it forms a well-bonded layer. Adhesion promoter for epoxy, polyurethane and polureic coatings, adhesion promoter for porous and deteriorated substrates, consolidating agent for cement and concrete. The support on which the polyurea or resinous system must be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 3%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. In case of presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to apply in advance the epoxy resin for "wet substrates" Syntech Pavidamp. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. Carefully mix component A to allow the correct homogenization of the fillers present; then combine it with component B in a suitable and large container. Then mix the compound with a mechanical stirrer at low speed until a homogeneous mixture is obtained. When the support is ready, apply SYNTECH POLIUREA PRIMER - EPOXY using rollers, brushes or spatulas trying to obtain a dry film. From 350 to 700 g for each square metre, based on the intervention carried out on the support (bush-hammering, shot peening, etc.), the porosity of the support itself and the incorporation or not of quartz sand in the particle size and quantity proportionate to the intervention to be implemented. Can 20 kg [A] - Canister 4 kg [B] - Kit: 1 Can 20 kg [A] + 1 Canister 4 kg [B]

Piccone in acciaio forgiato e temprato da 2kg e 2,5kg Occhio tondo Manico in legno di faggio Lunghezza del manico: 90cm

Pellet Swiss+26 ENplus sacchi da 15 kg in abete Dimensioni del pallet: Larghezza = 93 cm Altezza = 190 cm Profondità = 117 cm Stoccaggio pallet: Hai a disposizione un deposito esterno o un garage dove conservare i tuoi pallet di pellet e non farti cogliere impreparato se l'inverno è lungo e rigido. Qualità: pellet certificato DIN+ A1 e EN+ – 100% legno tenero, certificato senza additivi e diametro 6 mm. 1 SACCO 15 KG =EURO 3,00 1 PALLET 66 SACCHI MINIMO D'ORDINE 30 PALLET

La porta sezionale Lime modello Florida è realizzata con pannelli coibentati in acciaio preverniciato con spessore 0,5 mm, rivestiti con una speciale pellicola in materiale plastico idonea per la collocazione esterna e atta a garantire la massima durata nel tempo, che riproduce fedelmente l’effetto del legno su una superficie liscia, senza richiederne la stessa manutenzione. Caratteristica distintiva è l’assenza di doghe e la finitura liscia del pannello, che mettano in luce l’eleganza della semplicità. La versioni motorizzate si apre e si chiude in maniera semplice e veloce. Nelle versioni manuali, invece, l’apertura del porte è agevolata dalle molle torsionali. Le porte sezionali permettono un grande risparmio di spazio, elevato isolamento acustico e termico, e una estetica esterna che si può coordinare con il resto dell’abitazione.

La nostra attività principale è quella di importare dall'estero (Ungheria, Austria, Ucraina, Romania, Canada, Nuova Zelanda, ecc..) Pellet di qualità e venderlo ai privati o partite IVA. Grazie ad Asti Pellet potrai creare la tua scorta di pellet per l'inverno senza sforzo perchè ci occuperemo noi di consegnare a casa tua, nei giorni e nell'orario che preferisci, tutti i bancali di merce di cui a bisogno

Distribuzione e vendita online al dettaglio e all'ingrosso di levigatrici professionali delle migliori marche. Levigatrici orbitali, levigatrici roto-orbitali e levigatrici a nastro.

Distak-L Anti-adhesive release agent, emulsifiable in water, based on aromatic alkylates and specific agents, for easy removal of wooden formworks during dismantling. To be applied by spraying or roller to formworks dry and free of any soiling. Distak-L is emulsifiable with water in concentrations between 1:10 and 1:20. The action of Distak-L is of physical type: the properly emulsified and applied product forms an extremely thin separating film between the formwork and the fresh concrete, allowing easy detachment and surfaces free from stains and soiling. Release treatments for concrete castings in normal and pre-coated wooden formworks. Distak-L is a product that is ready to be emulsified in water at a concentration between 1:10 and 1:20. To obtain a correct emulsion it is essential to add the product to water and not vice versa. It is necessary to mix slowly and carefully, until a white, stable emulsion is obtained. With one litre of Distak-L, correctly applied, you can treat roughly about 50 m² of wood formwork. Caution: exceeding the product quantity can endanger the success of the casting. It is not suitable for metal formworks. Do not use this product with dilutions higher than those specified as they may not be stable and they are not effective. With 1 litre of Distak-L, correctly applied, it is possible to treat approximately 50 m² of wooden formwork. Packaging: 25-liter can Unit of Measure: €/l

Polished beech wood handle for sledge hammer, stoning hammer and splitting maul Length: 90cm Size: 49x35mm cm:90

Piccone in acciaio forgiato e temprato Occhio ovale Peso: 1,5kg Manico in legno di faggio Lunghezza del manico: 90cm SKU:37315L

Zappascure tipo solito in acciaio forgiato temprato Peso: 1800gr Occhio ovale Manico in legno di faggio Lunghezza del manico: 90cm SKU:86018IL

Rinfor Grout Col is a special cementitious formulation, being fibre-reinforced with READYMESH technology, enriched with reactive microsilicates with very high pozzolanic activity and special crystalliser additives that increase the end result and the durability. Mixed with water, it is able to forge micro-concretes with pourable rheology. Once hardened, the product offers exceptional physical-mechanical and ductility values. Ideal for the reinforcement and seismic adaptation of flooring in reinforced concrete, brick-concrete or corrugated sheeting or wood, by constructing a thin extradoxal structural screed along with beams, pillars, structural crosspoints and walls, by means of suitable liners. The rheological and physical-mechanical characteristics of the Rinfor Grout Col product render it extraordinarily effective in reinforcing structural elements in reinforced concrete and masonry. Adhered to the inside of caissons, confined within cavities or spread out over the extrados of foundations and lofts, Rinfor Grout Col allows for low thickness structural reinforcing, substantially devoid of additional metallic reinforcement. Rinfor Grout Col belongs to the HPFRC (High Performance Fibre Reinforced Concrete) family, permitting the structural designer to make use of the following characteristics: - Exceptional resistance and traction as well as exceptional values of shear stress adhesion on various supports which have been suitably roughened; - advantages in structural calculations prescribed for fracture mechanics, resistance to traction and of the ultimate material deformation; - minimum thicknesses applied with reinforcing effects which have been distinctly improved as against interventions with traditional reinforced concrete; - highly notable reduction of mass and minimizing of additional loads applied for structural reinforcing as against interventions with traditional reinforced concrete (practically nil additional loads in the case of the thickness of the coating corresponding with the depth of sacrificed surface); - anti-carbonatation barrier (practically zero penetration of CO2) and anti-oxidant barrier; - auto-healing of any micro-fissures exposed to contact with fluids, thanks to the particular crystallising additives; - increment of durability of the structures repaired with Rinfor Grout Col, thanks to the migration effect of the crystallising additives; - very high resistance to fire; - eco-sustainability - made up of 100% mineral and metallic materials, totally recyclable at end of life. From the environmental point of view, the Rinfor Grout Col product is characterised by the following advantages: - Ecological packaging (card-cardboard) - product based on hydraulic binders, selected aggregates and mineral additives with content of organic raw materials < 1% - practically nil VOC emissions during installation; once hardened, nil VOC emissions. - containing a fraction > 5% of sub-products from the production industry 100% recyclable at end of life. For seismic adaptation with absorption and transfer of pressure or traction during events with elevated dynamic forces (seismic, impacts, deflagration); - for structural reinforcing and seismic upgrading through coating of beams, pillars structural ties, walls; - for reinforcing and seismic upgrading with external, low thickness, structural screed for lofts in reinforced concrete, concrete masonry, corrugated sheeting, wood;
 - for fabrication of light, thin section, structural elements
; - for the repair of flooring with need for resistance against elevated static and dynamic stresses, together with exceptional values of resilience and resistance to impacts; - for reinforcing and precision anchoring of heavy and highly stressed machinery: E.g. wind turbines, turbines, precision machinery, etc. The support must be in good condition, clean, sufficiently coarse, without crumbling parts or dust, pressure washed and saturated with water before application. With concrete, the abrasiveness of the support must be > 3mm; to obtain this level of coarseness, techniques of hydro-scarifying, bush-hammering, mechanical chiselling, sand blasting with large grain may be considered. With the case of surfaces in strongly absorbent brick-work (lofts in brick cement with surfacing of parts in brick) or in the case in which it is impossible to saturate the support with water, contact our technical services to evaluate suitable adhesion primers, such as Syntech Pavisheer or Syntech RGS. Above all, when used as a surface covering of lofts in concrete, or as a repair to industrial flooring, providing anchoring roots by drilling the support is particularly useful for increasing resistance to cuts and adhesion to the support (diameter 18-20 mm, depth 20 mm), and accurately cleaning the surfaces of the holes before spreading the Rinfor Grout Col.

sanadry system is an innovative solution designed to address humidity issues in buildings. It combines a special fabric with a thermal adhesive to create a low-thickness micro-coating that effectively prevents moisture ingress. This product is particularly beneficial in areas prone to rising damp and condensation, providing a protective barrier that enhances indoor air quality. sanadry system is easy to apply and can be finished with breathable paints, ensuring a healthy living environment. Its effectiveness in moisture management makes it a crucial component in modern construction practices.

We Supply Best Quality Wood Pellets DIN PLUS / ENplus-A1 Wood Pellets Material: 100% Wood Diameter: 8mm Shape: Stick Length : 8-30 mm Calory : 4.400 - 4.600 Kcal / Kg Water Content: 8% Ash Content : <2% Packaging: Jumbo Bags, Bulk. Contact us for your inquiries

La porta sezionale Lime modello New York è realizzata con pannelli coibentati in acciaio zincato con spessore 0,5 mm, rivestiti con una speciale pellicola in materiale plastico idonea per la collocazione esterna e atta a garantire la massima durata nel tempo, che riproduce fedelmente l’effetto del legno su una superficie liscia, senza richiederne la stessa manutenzione. Caratteristica distintiva è la grande scanalatura centrale che divide in due doghe ogni pannello, che dona a questo modello uno stile ricercato. La versioni motorizzate si apre e si chiude in maniera semplice e veloce. Nelle versioni manuali, invece, l’apertura del porte è agevolata dalle molle torsionali. Le porte sezionali permettono un grande risparmio di spazio, elevato isolamento acustico e termico, e una estetica esterna che si può coordinare con il resto dell’abitazione.

We are offering certified European Standard Logs at affordable prices . The production of the design is strictly managed in order to ensure that quality levels are consistently high . All our logs are heat treated (ISPM15 compliant) and moisture controlled (kiln dried) . Please do get back to us for more information and details of our products and we shall get back to you with all the information needed .