Produkty dla instrumenty (157)

The high-temperature pressure transmitters of the 35XHTC series can be used at media temperatures of up to 300 °C. The remote electronics are designed for temperatures of up to 120 °C. They use digital compensation with a mathematical model to achieve an accuracy of 0,5 %FS – in the temperature range from 10 to 40 °C, this value even corresponds to the total error band. In addition to the digital RS485 interface, the X-line transmitters have a rangeable, analog current or voltage output. The standard model of the 35XHTC series has a G1/2 thread as pressure connection. Pressure Ranges:0…3 to 0…1000 bar Accuracy:±0,05 %FS Total Error Band:±0,5 %FS @ 20…300 °C Interfaces:RS485, 4…20 mA, 0…10 V Temperature Range:0…300 °C

The pressure transducers of the PD-10LHP series have been developed to measure differential pressure. These OEM pressure transducers have a single silicon diaphragm in their interior, which is pressurised from both sides and measures the pressure difference directly. This design enables them to measure tiny pressure differences even at an extremely high line pressure. Pressure Ranges:0…0,1 to 0…30 bar Line Pressure:600 bar Accuracy:±0,25 %FS Long Term Stability:±0,15 %FS Dimensions:⌀ 19 mm x 35 mm Temperature Range:-40…125 °C

Der Kraftsensor SC-002 ist bidirektional und resistiv. Das Messsystem besteht aus einem Halbleiter-Dehnungsmessstreifen. Die Messtaste besteht aus einem Schaft mit einem Durchmesser von 0,5 mm mit einer Positionierungskerbe zur Kalibrierung und Messung. Der Sensor ist speziell für eine hohe Eigenfrequenz ausgelegt..

The pressure transmitters of the 23SY series are designed for elevated requirements in industrial applications. Thanks to its modular concept, this series is highly flexible and makes it possible to realise customer-specific requirements in very little time. The sophisticated compensation circuit makes it possible to specify a narrow total error band. Pressure Ranges:0…0,1 to 0…1000 bar Accuracy:±0,25 %FS Total Error Band:±0,7 %FS @ -10…80 °C Interfaces:4…20 mA, 0…10V Temperature Range:-40…100°C

The pressure transmitters of the 22M series with brass housing were designed to be a reliable solution for automotive and industrial applications. They are homologated and can be used, for instance, to measure the content of the gas tank in bivalent vehicles. Pressure Ranges:0…5 to 0…250 bar Total Error Band:±2,0 %FS @ 0…80 °C Interfaces:0,5…4,5 V ratiom., 4...20 mA Special characteristics:Brass Homologation:E4-110R, E4-10R

Le logiciel M-TEST, utilisé avec un contrôleur de frein dynamométrique programmable Magtrol, fonctionne avec les freins dynamométrique ou les couplemètres Magtrol afin d’aider à la mesure et à l’analyse des caractéristiques de performance d’un moteur. Jusqu’à 63 paramètres peuvent être calculés et affichés en utilisant l’interface riche en fonctionnalités et les capacités graphiques de M-TEST. Développé en LabVIEW ™, M-TEST permet de tester une large palette de moteurs dans de multiples configurations. Les données générées peuvent être stockées, affichées et imprimées sous forme de tableaux ou graphiques, et facilement importées dans un tableur. Magtrol est également en mesure de personnaliser le logiciel afin de satisfaire aux demandes spécifiques de tests. Le logiciel M-TEST est offert comme une seule licence siège. Des sièges supplémentaires peuvent être achetés et ajoutée à la licence originale.... plus d'info www.magtrol.com

En tant que conditionneur de signal, l'AN1500M est utilisé pour le conditionnement et l’affichage de signaux provenant de capteurs (de force, de charge, de pression, de couple,...) équipés de jauges de contrainte en pont. En tant que moniteur de charge, il peut également recevoir tout signal compris dans la plage ±150mVDC issu d’un shunt ou de n’importe quel convertisseur ou transmetteur. Le moniteur de charge dispose de plages d’entrée (±150mV) et de tensions d’excitation (5V/10V) sélectionnables selon la sensibilité et le type de cellule. Deux méthodes de programmation de facteurs d’échelle permettent de travailler avec un grand nombre d’unités de mesure différentes. L’appareil est constitué d’un ensemble comprenant une carte de base, un affichage LED en trois couleur programmable et le système d’alimentation. Les fonctions de base de l’appareil comprennent l’affichage des variables d’entrée, les valeurs max. / min. et mémorisées (PEAK & VALLEY), fonction TARE avec RESET. Affichage:5 digits (-19999/+39999) a Affichage:Couleur programmable Affichage:14 mm hauteur Format:96 x 48 mm Cadence d'acquisition :20 valeurs / seconde fonction:HOLD, TARE, PEAK & VALLEY Montage:Panneau frontal IP65 Option:Sorties pour relais (seuils): 2SPDT ou 4SPST Option:Sortie analogique: 0...10V ou 4...20mA

The pressure transmitters of the 22S series were designed for use in automotive and industrial applications. They are homologated and every one of their elements has been configured for optimum reliability. In this steel version of the 22 series, all parts that come into contact with media are made of stainless steel (AISI 316L). Pressure Ranges:0…5 to 0…250 bar Total Error Band:±2,0 %FS @ 0…80 °C Interfaces:0,5…4,5 V ratiom., 4...20 mA Special characteristics:Steel 316L Homologation:none

Le MSD Mega Speed Dynamometer est la dernière innovation de Magtrol dans le domaine des tests de moteurs et de systèmes à très haute vitesse. Défié par ses nombreux clients dans le domaine dentaire et chirurgical, Magtrol repousse la limite à un niveau jamais atteint. L’effet de freinage est basé sur les courants de Foucault induits sur un disque en aluminium monté directement sur l’arbre du DUT (Device Under Test). Le couple est mesuré sans friction par un capteur de couple à réaction de 20 mN·m ayant une résolution de 0.01 mN·m. En raison de l’effet thermique sur le disque, le Mega Speed Dynamometer ne convient pas aux tests d’endurance, mais peut être utilisé pour générer une courbe rapide ou effectuer des tests point par point. Un capteur infrarouge surveille la température du disque et arrête le test en cas de surchauffe... plus d'info: www.magtrol.com Vitesse:≥ 400000min-1 Puissance de freinage:20W (5min) / 40W (15s) Couple nominal:20mN·m Précision:±0.2% Très faible inertie:~8x10-9 kg·m2 Norme:Médecine bucco-dentaire - Test de pièces à main et moteurs selon ISO 14457:2017 Option:Fixation pour moteurs ou instruments

MSD Mega Speed Dynamometer is the latest Magtrol innovation in the very high-speed motor and system testing. Challenged by its numerous customers in the Dental and Surgical field, Magtrol is pushing the limit to a level which was never reached. The braking effect is based on Eddy-Current induced on an aluminum disc directly mounted on the DUT (Device Under Test) shaft. Torque is measured frictionless by a 20 mN·m Reaction Torque Sensor having a resolution of 0.01 mN·m. Due to the thermal effect on the disc, the Mega Speed Dynamometer is not suit­able for endurance testing, but can be used to generate a fast curve or perform point to point testing. An infrared sensor monitors the temperature of the disc and stops the test in case of overheating. The disc can be designed and sized according to the motor parameters. The system is contactless therefore alignment is not critical and the inertia is very low (no friction, no residual or drag torque).... more info: www.magtrol.com Speed:≥ 400000min-1 Braking Power:20W (5min) / 40W (15s) Nominal:20mN·m Accuracy:±0.2% Very Low Inertia:~8x10-9 kg·m2 Standard:Dentistry - Handpiece and Motor Testing according to ISO 14457:2017 Optional:Motor or Handpiece Fixture

The series 6 pressure transducers are based on selected pressure transducers that are equipped with a pressure connection. Pressure Ranges:0…10 to 0…600 bar Accuracy:±1,0 %FS Pressure Connection:G1/4 Dimensions:HEX19 x 38mm Temperature Range:-10…80 °C

Description du produit Magtrol’s TORQUE 10 Software is an easy to use Windows® executable program, used to automatically collect torque, speed, mechanical power and angle data from Magtrol TS Series Torque Sensors or Magtrol TM Series Torque Sensors by using Model 3411 Torque Display. The data can be printed, displayed graphically or quickly saved/exported as a Microsoft® Excel spreadsheet.Caractéristique New graphical user interface has user friendly tabbed pages and menus for quick navigation Multi Language support (English, German, French) TS Series In Line Torque Sensors support via USB 3411 Torque Transducer Display support via USB and LAN 3410 Torque Transducer Display support via RS 232 Measured Parameter vs. Time Adjustable Sampling Rates Multi Axes Graphing Optional USB Device support for reading thermocouples Angle parameter available with TS Series and 3411

The pressure transmitters of the 4LC series use the chip-in-oil developed by KELLER, uniting a pressure measuring cell, digital temperature compensation and signal processing in a compact housing made of stainless steel or Hastelloy. The transmitters are extremely resistant to environmental influences and deliver compensated measurement results as an analog, ratiometric 0,5...4,5V output signal over a wide temperature range. Pressure Ranges:0…3 to 0…200 bar Accuracy:±0,25 %FS Total Error Band:±1,0 %FS @ 0…50 °C Interfaces:0,5…4,5 V ratiom Dimensions:⌀ 11 mm x 4,2 mm

Die Hysterese-Leistungsbremsen Serie HD sind vielseitig einsetzbar und hervorragend geeignet für Prüfaufgaben im mittleren Leistungsbereich bis maximal 14 kW bei intermittierendem Betrieb. Mit einem Hysterese-Bremssystem ausgerüstet erzeugt die Leistungsbremse schon im Stillstand ein Drehmoment. Der Motorprüfling kann demzufolge ab Leerlauf bis zum blockierten Rotor ausgemessen werden. Die Kühlung der Bremse erfolgt je nach Typ entweder durch Konvektion, oder mittels Druckluft. Da die Hysterese-Leistungsbremsen keine Wasserkühlung besitzen, werden ihre Leistungskenndaten sowohl für den kontinuierlichen als auch für den intermittierenden Betrieb angegeben. Alle Hysterese-Leistungsbremsen von Magtrol verfügen über eine Genauigkeit von ±0,25 % vom Skalenendwert, abhängig vom Typ und dessen Konfiguration. Zur optimalen Integration in das Messsystem bietet Magtrol kurze und lange Grundplatten an. ... mehr info www.magtrol. 16 StandardType mit Nenndrehmomenten:18mN·m ... 56.5N·m Motorenprüfung:vom Leerlauf bis zum blockierten Rotor durchführbar Genauigkeit:: ±0.25% (Skalenendwert) Kühlluftsensor:Als Schutz gegen Überhitzen und Fehlbedienungen Grundplatten:kurze oder lange Ausführung

The high-pressure transducers of the 7LHPI series have a robust housing made of Inconel, giving them optimum long-term stability for a range of OEM applications. The metal diaphragm is welded on front-flush and gap-free, separating off the piezoresistive pressure sensor, which is made of silicon, from the measuring medium. Every pressure transducer is measured over the entire pressure and temperature profile and is supplied with a detailed calibration sheet. Pressure Ranges:0…200 to 0…1000 bar Long Term Stability:±0,35 %FS Dimensions:⌀ 15 mm x 8 mm Temperature Range:-40…200 °C Material:Inconel 718

The differential pressure transmitters of the PRD-33X series are designed for accurate measurements in low pressure ranges with very high overload on both sides. In addition to the differential pressure sensor, which may only be exposed to gases at its rear face, the devices have an additional absolute pressure sensor that measures the line pressure. Both measured values are output via the digital RS485 interface and are the ideal basis for cryogenic tank monitoring. Pressure Ranges:0…0,35 to 0…3 bar Accuracy:±0,1 %FS Total Error Band:± 0,3 %FS @ -30…60 °C Line pressure:0…40 bar Interfaces:RS485 Special characteristics:Line pressure measurement

The pressure transmitters of the 7LHPD-Ei series for high pressure applications use the chip-in-oil technology developed by KELLER, uniting a pressure measuring cell, digital temperature compensation and signal processing in a compact housing made of stainless steel or Inconel. The transmitters are extremely resistant to environmental influences and delivery highly accurate measurement results as a digital output signal. The I2C interface and the low supply voltages make it easy to integrate in microcontroller-based systems. The extremely low power consumption is ideal for battery-operated devices. The D line is perfect for IoT solutions. Intrinsically safe – suitable for use in explosive atmospheres. Pressure Ranges:0…400 to 0…1000 bar Accuracy:±0,15 %FS Total Error Band:±1,0 %FS @ -10…80 °C Interfaces:I2C Dimensions:⌀ 15 mm x 8 mm

Automatisierung mit direkter Auswirkung: der BARImètre®-Automat kann bis zu 4 Referenzen gleichzeitig messen (bis zu 4 Kanäle). Laden Sie Ihre Maschine, drücken Sie START und der Automat erledigt den Rest.

The high-pressure transmitters of the 7LHPC series use the chip-in-oil technology developed by KELLER, uniting a pressure measuring cell, digital temperature compensation and signal processing in a compact housing made of stainless steel or Inconel. The transmitters are extremely resistant to environmental influences and deliver compensated measurement results as an analog, ratiometric 0,5...4,5V output signal over a wide temperature range. Pressure Ranges:0…200 to 0…1000 bar Accuracy:±0,25 %FS Total Error Band:±0,8 %FS @ -10…80 °C Interfaces:0,5…4,5V ratiom Dimensions:⌀ 15 mm x 8 mm

The high-pressure transducers of the 7LHP series have a robust housing made of stainless steel, giving them optimum long-term stability for a range of OEM applications. The metal diaphragm is welded on front-flush and gap-free, separating off the piezoresistive pressure sensor, which is made of silicon, from the measuring medium. Every pressure transducer is measured over the entire pressure and temperature profile and is supplied with a detailed calibration sheet. Pressure Ranges:0…200 to 0…1000 bar Accuracy:±0,5 %FS Long Term Stability:±0,25 %FS Dimensions:⌀ 15 mm x 8 mm Temperature Range:-40…150 °C Material:Steel 1.4435

The pressure transmitters of the 33X-Ed series use digital compensation with a mathematical model to achieve exceptional accuracy of 0,05 %FS – in the temperature range from 10 to 40 °C, this value even corresponds to the total error band. Additional measurements and selections can optionally be used to achieve a precision (and also, if calibrated in an accredited test laboratory, an accuracy) of 0,01 %FS. In addition to the digital RS485 interface, the X-line transmitters have a rangeable, analog current or voltage output. Pressure-proof housing – suitable for use in explosive atmospheres. Pressure Ranges:0…0,3 to 0…1000 bar Accuracy:±0,05 %FS Total Error Band:±0,1 %FS @ -10…80 °C Interfaces:RS485, 4…20 mA, 0…10 V Temperature Range:-40…120 °C

The pressure transmitters of the 9LD series use the chip-in-oil technology developed by KELLER, uniting a pressure measuring cell, digital temperature compensation and signal processing in a compact housing made of stainless steel or Hastelloy. The transmitters are extremely resistant to environmental influences and delivery highly accurate measurement results as a digital output signal. The I2C interface and the low supply voltages make it easy to integrate in microcontroller-based systems. The extremely low power consumption is ideal for battery-operated devices. The D line is perfect for IoT solutions. Pressure Ranges:0…1 to 0…200 bar Accuracy:±0,15 %FS Total Error Band:±0,7 %FS @ -10…80 °C Interfaces:I2C Temperature Range:-40…110 °C Dimensions:⌀ 19 mm x 5 mm

The pressure transducers of the 3L series have a small and compact design, making them ideally suited to OEM applications with limited installation space. The metal diaphragm is welded on front-flush and gap-free, separating off the piezoresistive pressure sensor, which is made of silicon, from the measuring medium. Every pressure transducer is measured over the entire pressure and temperature profile and is supplied with a detailed calibration sheet. Pressure Ranges:0...20 to 0...200 Accuracy:± 0,5 %FS Long Term Stability:± 0,5 %FS Dimensions:Ø 9,5 mm x 4,2 mm Temperature Range:20...30 °C

Wenn die Drehmomentregelung/Drehmomentmessung mit höchstmöglicher Leistung erfolgen muss, sind die Magtrol-Hysteresebremsen der Serie AHB ideal. Die durch die Bremsen verlaufenden Durchgänge ermöglichen eine Druckluftkühlung, die für eine hervorragende Wärmeableitung sorgt. Diese Konstruktion ermöglicht Dauerleistungen bis zu 3000Watt (5300Watt intermittierend). Die Verwendung von vorgespannten Lagern in Hysteresebremsen der Serie AHB ermöglicht den Betrieb von Drehzahlen bis zu 25000min-1 über längere Zeiträume. AHB-Bremsen werden zur einfachen Montage und Verdrahtung auf Klemmenblöcken montiert. Drehmoment:0.3 ... 24 Nm Drehzahl:bis zu 25000min-1 Leistung:5300 W Druckluftkühlung bietet hervorragende Wärmeableitung:- Zulässiger Eingangsluftdruck von bis zu 95PSI eliminiert die Notwendigkeit für einen Regler:- Ideal für Anwendungen mit niedrigem Drehmoment/hoher Drehzahl und mit außergewöhnlichen Leistungswer:- Magtrol Hysterese-Bremstechnologie bietet präzise Drehmomentsteuerung unabhängig von der Wellendrehz:- EMV-Empfindlichkeit entspricht den europäischen Normen:- Alle Dimensionierungen metrisch und Sockelmontage standardmäßig:- Konzipiert für die Verwendung mit dem T-Nuten- Grundplatten-Montagesystem der PT-Serie von Magtrol:- Eine grosse Auswahl von Zubehör und Systemoptionen zur Kreation eines einfachen und kostengünstigen :-

The pressure transmitters of the 25Y-Ei series with a front-flush separating diaphragm are designed for elevated requirements in industrial applications and are supplied with a G1/2" male pressure port. Thanks to its modular concept, this series is highly flexible and makes it possible to realise customer-specific requirements in very little time. The sophisticated compensation circuit makes it possible to specify a narrow total error band. Intrinsically safe – suitable for use in explosive atmospheres. Pressure Ranges:0…0,5 to 0…1000 bar Accuracy:±0,25 %FS Total Error Band:±0,7 %FS @ -10…80 °C Interfaces:4…20 mA, 0…10 V Temperature Range:-40…100 °C

The 9FLD series is a special version of the 9LD pressure transmitter. The flanged housing can be mounted using an O-ring or welded on. As with all D-line products, the chip-in-oil technology developed by KELLER is used here, uniting a pressure measuring cell, digital temperature compensation and signal processing in a compact housing made of stainless steel or Hastelloy.The I2C interface and the low supply voltages make it easy to integrate in microcontroller-based systems. The extremely low power consumption is ideal for battery-operated devices. The D line is perfect for IoT solutions. Pressure Ranges:0…1 to 0…30 bar Accuracy:±0,15 %FS Total Error Band:±0,7 %FS @ -10…80 °C Interfaces:I2C Dimensions:⌀ 17 mm x 5,5 mm

The low-cost data loggers of the DCX-18-ECO series have a rechargeable battery encased in a fully welded steel housing. The configuration software supplied (measurement interval, incident management, delayed measurement start etc.) also makes it easy to display data that has been read in a graph or chart, correct it using air pressure values, convert it into fill levels or other units, and export it. Pressure Ranges:0…10 to 0…100 mH2O Total Error Band:±0,2 %FS @ -10…40 °C Reading capacity:57'000 measuring points Dimensions:ø 18 mm Special characteristics:Rechargeable battery

Die Digimes Universel ist eine 5 KHz-Trägerstrombrücke für ohmsche, induktive oder differentielle Transformatorwandler in Voll- oder Halbbrückenschaltung. Die Empfindlichkeit ist durch den Benutzer zwischen 2 mV/V und 100 mV/V entsprechend sechs Messbereichen einstellbar. Verstärkung und Offset können mit Potentiometern eingestellt werden, um die Kalibrierung des Sensors zu ermöglichen. Es gibt auch das Digimes Compact, das einem Sensor gewidmet ist.

The capacitive pressure transmitters of the PD-41X series are designed for measuring differential pressure values in the mbar and µbar range. They use digital compensation with a mathematical model to achieve an accuracy of 0,1 %FS – in the temperature range from 10 to 40 °C, this value even corresponds to the total error band. In addition to the digital RS485 interface, the X-line transmitters have a rangeable analog current or voltage output. Pressure Ranges:0…0,03 to 0…0,3 bar Accuracy:±0,1 %FS Total Error Band:± 0,2 %FS @ 10…50 °C Line pressure:2 bar Interfaces:RS485, 4…20 mA, 0…10 V Special characteristics:Capacitive sensor

Magtrol's new PSD hand-held indicator is a stand-alone unit powered by 3 AA batteries or via USB. It is very compact (~160 x 80 x 50 mm) and can be easily carried and used on a civil engineering site, in a research & development office or laboratory as well as in production shop. Its case is ergonomic, waterproof (IP54) and protected by a rubber shock absorber. It is suitable to any type of strain gauge transducers, being a load cell, a load pin or a reaction torque sensor. The internal amplifier can process signal range of ±0.3 ... 5 mV/V. The new PSD Portable Display is very flexible and complies with the highest specification in terms of accuracy (0.01%) and measurement frequency (1600/s). It allows to store up to 16 programmable measurement ranges which can be configured either directly on the unit or via its USB interface and dedicated software (included). Multiple force or torque transducers can be connected for which actual data as well as the ... read more: www.magtrol. Accuracy:0.01% Measuring Rate: up to 1600 values per second Character Height:14mm