Produkty dla instrumenty (153)

Der Drehmoment-/Drehzahl-Signalaufbereiter TSC Reihe wird als Schnittstelle zwischen Wirbelstrom– oder Magnet-pulverbremsen von Magtrol und einem DSP 7000-Controller eingesetzt. Die Speisung des TSC Reihe Signalaufbereiters erfolgt durch den DSP 7000-Controller. Der Signalaufbereiter verstärkt und filtert das Drehmomentsignal, dient der Speisung und dem Anschluss der Leistungsbremsen-Drehzahlaufnehme Offset:±0.2% (Vom Endwert) Symmetrie:±0.1% (Vom Endwert) Bandbreite (3dB einpolig):20Hz Offsetdrift:<100ppm/ °C Empfindlichkeitsdrift:<50ppm/ °C Netzspannung:±20 - ±30V Strom:40mA nenn / 45mA max Drehmoment-Ausgangsspannung:5VDC ±0.2% Max. Ausgangsstrom:5mA Min. Ausgangslast:1kΩ

The DCX-22 data loggers achieve greater measurement accuracy than loggers with a smaller diameter. Thanks to their long-life battery, they can keep measuring the water level, water pressure and temperature for years (up to 10 years at a rate of one measurement per hour). The data logger can be configured using the supplied software (measurement interval, incident management, delayed measurement start etc.) and data that has been read can be displayed in a graph or chart, corrected using air pressure values, converted into fill levels or other units, and exported. Pressure Ranges:0…5 to 0…100 mH2O Total Error Band:±0,1 %FS @ -10…40 °C Reading capacity:57'000 measuring points Dimensions:ø 22 mm Special characteristics:Also available in ECO design

The series 13 pressure transducers have internal water cooling and are suitable for use in media temperatures of up to 350 °C. Typical applications include superheated steam circuits, engine test benches or chemical process monitoring. Pressure Ranges:0…10 to 0…1000 bar Accuracy:±0,5 %FS Pressure Connection:M14 x 1,2 Dimensions:⌀ 28 mm x 48 mm Temperature Range:20…350 °C

The pressure transducers of the PD-10L series have been developed to measure differential pressure. These OEM pressure transducers have a single silicon diaphragm in their interior, which is pressurised from both sides and measures the pressure difference directly. This design enables them to measure tiny pressure differences even at an extremely high line pressure. Pressure Ranges:0…0,1 to 0…30 bar Line Pressure:200 bar Accuracy:±0,25 %FS Long Term Stability:±0,15 %FS Dimensions:⌀ 19 mm x 26 mm Temperature Range:-40…125 °C

Magtrol’s Model 3411 Torque Display is designed for use with all Magtrol TS, TM, TMHS, TMB and TF Torque Transducers. This easy-to-use device powers the transducer and utilizes high speed processing to display torque, speed and mechanical power. It includes a tare function to help offset any slight residuals caused by couplings or suspended loads. The 3411 may also be used with any torque sensors requiring 24 V DC power (500 mA max.) with ± 5 V DC torque output (± 10 V DC max.) and open collector, TTL or CMOS output for the speed signal.

The DCX-16 data loggers have a diameter of just 16 mm and can be used in tight spaces. Thanks to their long-life battery, they can keep measuring the water level, water pressure and temperature for years (up to 10 years at a rate of one measurement per hour). The logger can be configured using the supplied software (measurement interval, incident management, delayed measurement start etc.) and data that has been read can be displayed in a graph or chart, corrected using air pressure values, converted into fill levels or other units, and exported. Pressure Ranges:0…10 to 0…100 mH2O Total Error Band:±0,1 %FS @ -10…40 °C Reading capacity:57'000 measuring points Dimensions:ø 16 mm Special characteristics:Slender design

The pressure transmitters of the 4LD series use the chip-in-oil technology developed by KELLER, uniting a pressure measuring cell, digital temperature compensation and signal processing in a compact housing made of stainless steel or Hastelloy. The transmitters are extremely resistant to environmental influences and delivery highly accurate measurement results as a digital output signal. The I2C interface and the low supply voltages make it easy to integrate in microcontroller-based systems. The extremely low power consumption is ideal for battery-operated devices. The D line is perfect for IoT solutions. Pressure Ranges:0…3 to 0…200 bar Accuracy:±0,15 %FS Total Error Band:±0,7 %FS @ 0…50 °C Interfaces:I2C Dimensions:⌀ 11 mm x 4,2 mm

The pressure transmitters of the 9LC series use the chip-in-oil developed by KELLER, uniting a pressure measuring cell, digital temperature compensation and signal processing in a compact housing made of stainless steel or Hastelloy. The transmitters are extremely resistant to environmental influences and deliver compensated measurement results as an analog, ratiometric 0,5...4,5V output signal over a wide temperature range. Pressure Ranges:0…1 to 0…200 bar Accuracy:±0,25 %FS Total Error Band:±0,8 %FS @ -10…80 °C Interfaces:0,5…4,5 V ratiom Temperature Range:-40…150 °C

The Magtrol 7500 Series Power Analyzer is an easy-to-use instrument ideal for numerous power measurement applications. From DC to 80 kHz AC, the 7500 measures volts, amps, watts, volt-amps, frequency, crest factor, Vpeak, Apeak and power factor in one convenient display. They may be used either as stand-alone instruments or in conjunction with any Magtrol Hysteresis, Eddy-Current or Powder Brake Dynamometer; any Magtrol Dynamometer Controller and M-TEST Software for more demanding motor test applications. If currents continuously reach above 20 amps, an external sensor must be used. APPLICATIONS: - AC/DC Motors - Lighting Fixtures/Ballasts - Office Equipment - Household Appliances - Power Tools - HVAC Equipment - Calibration of Test and Measuring Instruments - Transformers The 7500’s data transfer rate makes it ideal for both static and dynamic tests. Single/three-Phase Capabilities:For single (7510) or three-phase (7530) power measurements Ranges:Up to 600 Vrms @ 20 A continuous duty Interfaces:USB & IEEE-488 Data transfer rates:Up to 100 per second Accuracy:Up to 0.1% Vacuum Fluorescent Display:High-quality, easy-to-read, customizable readout displays volts, amps, power and power factor Measurement:Continuous or cycle-by-cycle Bandwidth:DC up to 80 kHz Input Power:Accepts 120/240 Vrms, 60/50 Hz power at 20 VA max Auto ranging:Automatically scales instrument for most accurate range Isolation:1000 Vrms to earth, 750 Vrms line-to-line Average:Displays running average of amps, volts and watts Peak Hold:Stores the highest value read. Values can include amps, watts and volts in any combination Calibration Certificate:NIST Traceable Rack Mounting:19” (482.6 mm) with handles

The series 8 high-pressure transducers have been developed for applications in high pressure ranges with high levels of pressure endurance and rapid pressure peaks, as are found for instance in hydraulic systems or the oil industry. Pressure Ranges:0…10 to 0…1000 bar Long Term Stability:±0,5 %FS Dimensions:⌀ 15 mm x 13 mm Temperature Range:-55…150 °C Material:Stahl 1.4435

The DCX-25PVDF data loggers have been specially designed for use in aggressive liquids such as brackish water and sewage. The housing is made of polyvinylidene fluoride and the installed pressure transducer is available in Hastelloy C-276 or titanium 6AL-4V. Thanks to their long-life battery, they can keep measuring the water level, water pressure and temperature for years (up to 10 years at a rate of one measurement per hour). The logger can be configured using the supplied software (measurement interval, incident management, delayed measurement start etc.) and data that has been read can be displayed in a graph or chart, corrected using air pressure values, converted into fill levels or other units, and exported. Pressure Ranges:0…10 to 0…100 mH2O Total Error Band:±0,1 %FS @ -10…40 °C Reading capacity:57'000 measuring points Dimensions:ø 25 mm Special characteristics:Special plastic housing

The MPX pressure calibrator is a high-precision calibration instrument for pressures between -0,85 bar and 25 bar (after taring to ambient pressure). The functional calibrator is supplied in a sturdy carrying case and pressure can be quickly generated manually. It is therefore ideal for use in the field. The pressure is measured by the integrated LEX1 manometer and is both shown on the display and output via the RS485 interface. Additional functions such as zero point resetting, peak and trough pressure value indication and leak measurement make it even easier to take measurements. Pressure Ranges:-0,85…25 bar Accuracy:0,05 %FS Interfaces:RS485 Display:5-digit LCD display Special characteristics:For air pressure

The pressure transmitters of the 8LC series use the chip-in-oil developed by KELLER, uniting a pressure measuring cell, digital temperature compensation and signal processing in a compact housing made of stainless steel or Hastelloy. The transmitters are extremely resistant to environmental influences and deliver compensated measurement results as an analog, ratiometric 0,5...4,5V output signal over a wide temperature range. Pressure Ranges:0…1 to 0…200 bar Accuracy:±0,25 %FS Total Error Band:±0,8 %FS @ -10…80 °C Interfaces:0,5…4,5V ratiom Dimensions:⌀ 17 mm x 7 mm

The low-cost OEM pressure transducers of the 6S series are based on a piezoresistive measuring cell with a brazed metal diaphragm in a steel housing. Pressure Ranges:0…0,3 to 0…1000 bar Accuracy:±0,5 %FS Pressure Connection:G1/4 Dimensions:HEX22 x 34mm Temperature Range:-20…80 °C

The ultra-fast M5HB pressure transmitter can process pressure changes with a bandwidth of 50 kHz. This is achieved by means of the continuous analog signal that is adjusted by a digital circuit in real time and is amplified to a standardised 0...10V signal. The miniature sensor head with a fine M5 thread can withstand temperatures of up to 180 °C, is overload-proof up to a magnitude of five times the measuring range, and is also resistant to vibrations. Pressure Ranges:0…3 to 0…30 bar Accuracy:±0,1 %FS Total Error Band:±0,5 %FS @ -20…125 °C Interfaces:0…10 V Temperature Range:-40…180 °C

The high-pressure transducers of the 7LHPTi series have a robust housing made of titanium, giving them optimum long-term stability for a range of OEM applications. The metal diaphragm is welded on front-flush and gap-free, separating off the piezoresistive pressure sensor, which is made of silicon, from the measuring medium. Every pressure transducer is measured over the entire pressure and temperature profile and is supplied with a detailed calibration sheet. Pressure Ranges:0…50 to 0…1000 bar Long Term Stability:±0,25 %FS Dimensions:⌀ 15 mm x 8 mm Temperature Range:-50…150 °C Material:Titan grade 2

Als Signalaufbereiter wird der AN1500M zur Aufbereitung und Anzeige von Signalen verwendet, die von Sensoren (Kraft, Last, Druck, Drehmoment, ...) mit Dehnungsmessstreifen in Brückenschaltung stammen. Als Lastmonitor kann er auch jedes Signal im Bereich von ±150mVDC von einem Shunt einem Konverter oder einer beliebigen Art von Transmitter empfangen. Der Lastmonitor bietet wählbare Eingangsbereiche (±150mV) und Erregerspannungen (5V, 10V), um Wägezellen mit verschiedenen Typen und Empfindlichkeiten zu unterstützen. Zwei Programmiermethoden ermöglichen die Skalierung des Messgeräts für den Betrieb in den gewünschten technischen Einheiten. Das Basisgerät ist eine gelötete Baugruppe, die aus einer Hauptplatine, einer dreifarbigen programmierbaren Anzeige und einem Stromkreis besteht. Zu den Standardmerkmalen gehören das Ablesen der Eingangsvariablen sowie Fern- HOLD, Ablesen von Minimal-/Maximalwerten (PEAK & VALLEY), TARA- und Reset-Funktion,... Anschluss für 1 oder 2 Messwertaufnehme:5/10V; 60mA DC Anzeige:5 Digits (-19999/+39999) mit programmierbarer Farbe Anzeige:LED 14mm Höhe Messrate:20 Messungen pro Sekunde Abmessungen:Standard Format 96 x 48 mm Funktionen:HOLD, TARE, PEAK & VALLEY Befestigung:Frontplatte IP65 (Einsatz in Innenräumen) Option:Relais-Ausgänge (Schwellwerte): 2SPDT / 4SPST Option:Analog-Ausgang: 0...10V / 4...20mA

Die Drehmomentanzeige Typ 3411 von Magtrol wurde speziell für den Einsatz mit TS-, TM-, TMHS-, TMB- und TF Drehmomentaufnehmern entwickelt. Dieses leicht bedienbare Gerät dient auch der Speisung der Aufnehmer und anzeigt der Messsignale (Drehmoment, Drehzahl, mechanische Leistung) mittels eines Hochgeschwindigkeits Prozessors. Die Drehmomentanzeige verfügt über eine Tarierfunktion zur Kompensierung allfälliger Restdrehmomente von Kupplungen oder aufgehängter Lasten. Die Anzeige Typ 3411 kann ebenfalls mit Aufnehmern eingesetzt werden, welche mit 24 V DC (500 mA max.) betrieben werden, eine Drehmoment- Ausgangsspannung von ± 5 V DC (± 10 V DC max.) liefern und einen Drehzahlausgang mit offener Kollektor, TTL oder CMOS besitzen.

The pressure transmitters of the 7LD-Ei series use the chip-in-oil technology developed by KELLER, uniting a pressure measuring cell, digital temperature compensation and signal processing in a compact housing made of stainless steel or Hastelloy. The transmitters are extremely resistant to environmental influences and delivery highly accurate measurement results as a digital output signal. The I2C interface and the low supply voltages make it easy to integrate in microcontroller-based systems. The extremely low power consumption is ideal for battery-operated devices. The D line is perfect for IoT solutions. Intrinsically safe – suitable for use in explosive atmospheres. Pressure Ranges:0…3 to 0…200 bar Accuracy:±0,15 %FS Total Error Band:±0,7 %FS @ -10…80 °C Interfaces:I2C Dimensions:⌀ 15 mm x 5 mm

Die Drehmomentsensoren TSF-000 bis TSF-5 sind bidirektional und induktiv. Das Messsystem besteht aus einer Achse, die zur reibungsfreien Drehmomentmessung auf flexiblen, quergefederten Drehpunkten montiert ist. Der Drehwinkel der Achse, der proportional zum zu messenden Drehmoment ist, wird mit einem induktiven Trägerfrequenzsensor gemessen. Diese kleine Winkeldrehung (ungefähr 1° für den Messbereich) gewährleistet eine gute Linearität und eine praktisch vernachlässigbare Hysterese.

The compact pressure transponders consist of a digital, extremely robust D-line pressure transmitter and a passive RFID module. They obtain their power from the reader and therefore do not require a power connection or battery replacement. The 21D RFID transponders are therefore perfect for convenient on-side reading of instantaneous values, e.g. during inspection tours or safety checks on large vehicles. Pressure Ranges:0…3 to 0…1000 bar Accuracy:±0,15 %FS Total Error Band:±0,7 %FS @ -10…80 °C Reading capacity:none Special characteristics:Pressure transponder (passive)

The pressure transmitters of the 35XHT series are suitable for use in media temperatures up to 150 °C and can therefore be used in bioreactors and autoclaves that have to be sterilised regularly. They use digital compensation with a mathematical model to achieve an accuracy of 0,15 %FS – in the temperature range from 10 to 40 °C, this value even corresponds to the total error band. In addition to the digital RS485 interface, the X-line transmitters have a rangeable, analog current or voltage output. The standard model of the 35XHT series has an Ingold fitting as pressure connection. Pressure Ranges:0…1 to 0…30 bar Accuracy:±0,05 %FS Total Error Band:±0,15 %FS @ 20…120 °C Interfaces:RS485, 4…20 mA, 0…10 V Temperature Range:-20…150 °C

Die motorisierten 4-Quadranten-Leistungsprüfstände von Magtrol bieten eine erweiterte Prüfflexibilität gegenüber einem typischen Bremsenprüfstand. Durch die Möglichkeit, den zu prüfenden Motor (MUT) vor Beginn einer Prüfung auf synchrone Drehzahl zu bringen, wird die Wiederholbarkeit verbessert. Da die Motorwicklungen vor dem Start eines Rampentests die Umgebungstemperatur erreicht haben, ist die Wattzahl konsistenter. Kundenspezifische Software ist erforderlich, um die spezifischen Anforderungen jeder einzelnen Kundenapplikation zu erfüllen. Da die Drehmomentaufnehmer der TM-Serie von Magtrol zwischen dem Motor der Leistungsbremse und dem MUT eingesetzt werden, sind wir in der Lage, die Reibung und den Luftwiderstand des MUT zu messen.

Magtrol kundespezifische Motorenprüfstände (CMTS) sind PC-basierte, schlüsselfertige Systeme, die benutzerdefiniert hergestellt werden, um Ihre speziellen Anforderungen zur Motorenprüfung zu erfüllen. Durch Integration von Magtrol Motorenprüfständen mit Speisegeräten, anpassungsfähigem Zubehör, kundenspezifischen Tischen und Schränken, Druckern etc., ist das Magtrol Engineering-Team in der Lage, PC-basierte, schlüsselfertige Systeme und modulare Prüfstände fast jeder Motorprüfanwendung anzupassen.

Le conditionneur de signal AN2000C est utilisé pour le conditionnement et l’affichage de signaux provenant de capteurs (de force, de charge, de pression, de couple,...) équipés de jauges de contrainte en pont. Il peut également recevoir tout signal compris dans la plage ±300mVDC issu d’un shunt, de n’importe quel convertisseur ou transmetteur. Le conditionneur offre des plages d'entrée sélectionnables (max. ±300mV) et de tensions d’excitation (5/10V) sélectionnables selon la sensibilité et le type de cellule. Deux méthodes de programmation de facteurs d’échelle permettent de travailler avec un grand nombre d’unités de mesure différentes. L’appareil est constitué d’un ensemble comprenant une carte de base, un affichage LED et le système d’alimentation; à cela peut s'ajouter les circuits d’entrée en option. Les fonctions de base de l’appareil comprennent l’affichage de la variable d’entrée, HOLD, la lecture des valeurs max./min. (PEAK & VALLEY), TARE et RESET. 1...4 alimentations de capteurs:5V/10V; 120mADC Affichage:5 Digits (±32000) Affichage:LED hauteur 14mm Cadence d'acquisition :16 acquisitions par seconde fonction:HOLD, TARE, PEAK & VALLEY Panneau frontal:IP65 (utilisation en intérieur) Option:Sorties pour relais (seuils): 2SPDT ou 4SPST Option:Sortie analogique: 0...10V ou 4...20mA

Die Kraftsensoren LC-01 bis LC-10 sind bidirektional und induktiv. Das Messsystem besteht aus einem Sensor, dessen beweglicher Kern mit zwei Blattfedern gekoppelt ist. Die Auslenkung dieser Blattfedern, die proportional zu der zu messenden Kraft ist, wird mit einem induktiven Trägerfrequenzsensor gemessen. Der Messschlüssel, der in den beweglichen Kern integriert ist, ist austauschbar und ermöglicht die Verwendung von Spezialschlüsseln.

As a Signal Conditioner, the AN1500M is designed to process and display signals coming from various types of transducers (weight, load, pressure, torque, etc.) that use standard strain-gauge bridges. As a Load Monitor the AN1500M can also receive any signal within the ±150mVDC range coming from a shunt, a converter or any type of transmitter. The Load Monitor provides selectable input ranges (±15mV, ±30mV, ±150mV) and excitation voltages (5V, 10V) to accommodate cells of various types and sensitivities. Two programming methods allow scaling of the meter to operate in the desired engineering units. The basic instrument is a soldered assembly composed of a main board, a tri-color programmable display and a power circuit. Standard features include the reading of the input variable as well as remote (HOLD), the reading and memorization of minimum/maximum values (PEAK/VALLEY), TARE and RESET function, and a full complement of programmable logic functions. 1 or 2 Transducer Power Supplies:5/10V; 60mA DC Display:5 Digits (-19999/+39999) with programmable color; Display:LED 14mm height Dimensions:standard format 96 x 48mm Acquisition rate:20 Acquisitions per second Functions:HOLD, TARE, PEAK & VALLEY Mounting:IP65 front panel (indoor use) Programmable with front-panel keys:- Quick wiring using WAGO connectors:- Optional:▪ Relay Outputs (thresholds): 2SPDT or 4SPST Optional:Analog Output: 0...10V or 4...20mA

Les couplemètres de Magtrol permettent de réaliser des mesures de couple et de vitesse de rotation très précises sur une plage extrêmement étendue. Chaque capteur de couple est équipé d’un circuit électronique de conditionnement des signaux mesurés qui génère un signal de sortie entre 0 et ±10VDC pour le couple et possède une sortie open collector pour le signal de vitesse de rotation. Protégés contre les surcharges, stables à long terme et possédant une excellente immunité contre les bruits de fond, les couplemètres de Magtrol sont connus pour leur extrême fiabilité. Afin de pouvoir offrir en tout temps une solution garantissant le meilleur rapport prix/performances à sa clientèle, Magtrol met 3 modèles de couplemètres à disposition: les modèles TMB Series, parfait pour toute application standard, les modèles TM Series lorsqu’une grande précision est requise et enfin les modèles TMHS Series pour des mesures de grande précision à très hautes vitesses de rotation. Mesure de couple:0.1N·m ... 10kN·m Précision:<0.1% Surcharge admissible:200% Limite de rupture:>400% Vitesse de rotation:jusqu'à 50000min-1 Tension d’alimentation:20VDC ... 32VDC

Les conditionneurs de signaux de couple et de vitesse de rotation TSC Série sont utilisés pour raccorder les freins dynamométriques à courant de Foucault (WB Série) ou à poudre magnétique (PB Série) à un contrôleur de frein dynamométrique DSP 7000. Alimenté par le DSP 7000, ces conditionneurs amplifient et filtrent les signaux de couple. Ils alimentent également le capteur de vitesse de rotation placé dans les freins dynamométriques. Offset:±0.2% (à pleine échelle) Symétrie:±0.1% (à pleine échelle) Bande passante (3dB unipolaire) :20Hz Dérive de l’offset:<100ppm/ °C Dérive de la sensibilité:<50ppm/ °C Tension d’alimentation:±20 - ±30V Courant :40mA nominal / 45mA max. Tension de sortie couple:5VDC ±0.2% Courant de sortie max.:5mA Charge de sortie min.:1kΩ

The AN2000C Signal Conditioner & Display is designed to process and display signals coming from various types of transducers (weight, load, pressure, torque, etc.) that use standard strain-gauge bridges. It can also receive any signal within the range ±300mVDC coming from a shunt, a converter or any type of transmitter. The Conditioner provides selectable input ranges (max. ±300mV) and excitation voltages (5V, 10V) to accommodate cells of various types and sensitivities. Two programming methods allow scaling of the meter to operate in the desired engineering units. The basic instrument consists of a PCB assembly including the main board, the display and the power supply filter, to which the A/D conversion circuit and the input option are added. The functions of the basic instrument include the display of the input variable as well as the remote freezing of the display (HOLD), the reading of the stored minimum and maximum values (PEAK & VALLEY) and the TARE function with RESET. 1...4 Transducers Power Supplies:5V/10V; 120mADC Display:5 Digits (±32000) Display:LED 14mm height Dimensions:Standard format 96 x 48mm Acquisition rate:16 Acquisitions per second Functions:HOLD, TARE, PEAK & VALLEY Mounting:IP65 front panel (indoor use) Programmable with front-panel keys:- Quick wiring using WAGO connectors:- Optional:Relay Outputs (thresholds): 2SPDT or 4SPST Optional:Analog Output: 0...10V or 4...20mA