Produkty dla instrumenty (2511)

Tablet for mobile use Eight analog inputs with up to 100kHz bandwidth. Various options available for signal conditioning and power supply of connected sensors. •,8 analog input channels •,Up to 100kHz bandwidth synchronously sampled across all channels •,16/24 bit resolution with 110+dB signal-to-noise ratio •,4h battery life •,Internal SSD with up to 256GB storage capacity (over 12h data recording) •,Compact dimensions (270x230x38mm) and low weight (2.5kg) •,Built-in 10" touchscreen for easy configuration and display of measurement and analysis results •,2xUSB port, 1x Ethernet interfaces, connection for external 12V power supply •,Various Signal Conditioning Options (in development)

Lesekopf zum Anschluß an Positionsanzeigen LG20 und LH70 Serie Ausgangssignal: TTL A/B Quadratur-Signal, konform mit EIA-422 Maximale Auflösung: 10μm Maximale Ansprechgeschwindigkeit: 300m/min (variiert je nach Lesekopf und Einstellung) Extrem unempfindlich selbst bei rauesten Umgebungsbedingungen (IP65) Resistent gegenüber Öl, Staub, Vibration und Schock Auflösung:10µm Ausgangssignal:TTL Linedriver RS422 Spannungsversorgung :5V DC Max. Ansprechgeschwindigkeit :5m/s Zum Anschluß an Positionsanzeigen :LG20, LH70, LY70- Serien Kompatible mit Längenmesssystem:SL110 oder SL130

There are several steps to be taken for a successful test and for this to work in a targeted and efficient manner, a lot of planning and preparation is necessary. We therefore create the following from your ideas or your order: the data specification, including measurement uncertainty requirement; the test concept; Design of experiments; the specifications for test bench and measurement technology; the specification for the test specimen; Implementation planning.

The Dragonfly battery is designed to enable measurements in areas where power is not available from the local power grid. •,Capacity of 100Wh (power supply of a typical Dragonfly amplifier for up to 10h runtime) •,One battery module can also power several Dragonfly amplifiers (with correspondingly shortened runtime) •,Several modules can be combined to extend battery life. •,Can be used as a UPS (Uninterruptible Power Supply).

The mains-driven panel meter RM-32 provides a continuous and precise measurement of irradiance with preamplified UV sensors. The integrated electronics produce a signal voltage that is transmitted to the radiometer, so that inferences are minimized. Different UV and visible spectral ranges, measuring ranges, and output signals can be selected to match the measurement task. The current irradiance is shown on a 3.5-digit digital display. The lamp state with respect to two threshold values is indicated by LEDs. Two relay contacts can be used for switching warning and failure signals. With its optional USB, RS232 or RS485 interface the RM-32 can be used to monitor ultraviolet (UV) irradiance. Control of light sources and irradiation systems Precise measurement of irradiances UV monitor for process control and documentation Dimensions:DIN 43700 96 x 48 mm Depth:~ 115 mm Weight:410 g Mains:230 V, 50 Hz, 3 W Operating temperature:0 to 40 °C

The BS-03 is a medium-sized, rugged irradiation chamber for time- or dose-controlled irradiation of samples with UVA, UVB, or UVC. The chamber can be fully equipped for one of the spectral ranges UVC, UVB, or UVA to achieve the highest irradiance. Alternately, the use of two separately controlled lamp groups for different spectral ranges allows for especially flexible operation of the chamber. The interior irradiation chamber has a base area of 68 x 49 cm² and a height of 32 cm. The sliding sample carrier facilitates loading and unloading. With a load of up to 20 kg, this can withstand all demands. The sample chamber operating temperature is about 25°C so that thermal damage to the specimen is avoided. Due to the high uniformity of the irradiation, the samples may be positioned in any order. Two irradiation controls are available for the BS-03: the UV-MAT and the UV-MAT Touch. Interior chamber:68 x 49 x 32 cm Dimensions:77 x 64 x 68 cm Power consumption:300 W Lamp lifetime UVA:up to 4.000 h Lamp lifetime UVB:up to 4.000 h Lamp lifetime UVC:up to 9.000 h Irradiance UVA:8 mW/cm² Irradiance UVB:2.4 mW/cm² Irradiance UVC:10 mW/cm²

The HP-120i is a high-intensity short arc light source for quick UV spot curing within seconds. As a microprocessor controlled spotlight source with light guide, HP-120i is a reliable and economical „cold“ light source for irradiation with high-intensity UV-A radiation and blue light. The heat transfer in the material is minimized due to the absence of ineffective red and near-infrared radiation. The spotlight source uses fiber-optic cables in various configurations for flexible irradiation of one to four points. Depending on the light guide, UV-A irradiances of up to 15,000 mW/cm² can be achieved. The exposure time can be set through a digital timer with a resolution of 0.1 s. The shutter can also be switched by a foot switch or via a PLC system controller by an external contact. The typical lamp life is 2,000 hours. To achieve uniform irradiation, the lamp power is stabilized. Lamp lifetime:2000 h (typical) Dimensions:305 mm x 358 mm x 145 mm Weight:~ 8,2 kg Mains:110 - 230 VAC, 50/60 Hz Operation temperature:5 to 40 °C

The water-proof sensor UVX-SE serves as robust, long-term stable measuring heads for the precise measurement of UV irradiances in production lines, that have to be wet cleaned. The sensors are calibrated with traceability to the PTB (Physikalisch Technische Bundesanstalt, the German national test authority) and can be exposed to pressure of up to 10 bar. The sensors are available in eight spectral ranges and two measuring ranges. This allows the sensors to be optimally adapted for the application. The integrated electronics produce a signal that is transmitted to the PLC or panel meter, so that inferences are minimized. Operating voltage and output signal can be selected to match the measurement task or PLC interfaces. For small control tasks, the sensor UVX-SE can be connected to RM-32, which shows current irradiance on a 3.5-digit digital display and switches two relay contacts with adjustable warning and alarm signals. Measuring range:0 - 200 mW/cm² Measuring range option:0 - 20 mW/cm² Connector:G 3/4“ Dimensions:see drawing Weight:~420 g

Die Messdaten des Messtaster können über Ethernet, EtherNet/IP, PROFINET oder EtherCAT Feldbus an eine SPS gesendet werden Feldbuskompatibles Interfacemodul: MG80-NE (Ethernet) / MG80-EI (EtherNet/IP) / MG80-PN (PROFINET) / MG80-EC (EtherCAT) An jedes Hauptmodul können bis zu 16 Zählermodule MG80-CM für Messtaster angeschlossen werden An MG80-NE können über max. 3 LINK-Verbindungen bis zu 64 MG80-CM bzw. Messtaster angeschlossen werden An MG80-EI/PN können über LINK-Verbindungen bis zu 255 MG80-CM bzw. Mestaster angeschlossen werden An MG80-EC können theoretisch über LINK-Verbindungen bis zu 65.535 MG80-CM bzw. Mestaster angeschlossen werden MG80-CM Zählermodul zum Anschluss von einem Messtaster der Serie DK oder DT (mit MT13) Einfache Installation auf DIN-Montageschiene LZ80-K1/K2 E/A Modul für MG80-EI, MG80-PN und MG80-EC Ausgestattet mit 8 Eingängen und 8 Ausgängen Interfacemodule für :Ethernet ; Ethernet/IP ; PROFINET; ETHERCAT Kompatible Messtaster :DK-Serie und DT-Serie mit MT13 Adapter

The very high irradiances of up to 39,000 mW/cm² and the compact dimensions characterize the UV-LED Spots and allow extremely short process times. For this purpose, the UV-LED is focused at the desired working distance. The UV-LED Spot P is suitable for automated and manual bonding. For applications such as bonding, potting or fluorescence excitation, the wavelengths 365, 385, 395, 405 and 450 nm are available. With the variety of wavelengths as well as the exchangeable optics, you remain particularly flexible and can upgrade and change over at any time. For controlling the UV-LED Spot P, we offer the LedControl S as a table top device or the LedControl DC for DIN rail mounting. With the LedControl S and DC UV LED controllers, the ultraviolet LED output can be set between 2% and 100%. Wavelength:365, 385, 395, 405 o. 450 nm Dimensions, Spot P:Ø 15 x 143 mm Dimensions, Spot P short:Ø 15 x 60 mm Cable length:1,5 m Weight:~130 g

Miniature Metal Bellows Coupling axial pluggable, with collet clamps Backlash-free miniature metal bellows coupling with clamp hubs For shaft diameter from 3 – 25 mm High torsional stiffness, compensation of shaft misalignment at low restoring forces Easy assembly with friction-locked clamp hubs Perfect bellows coupling for encoders, tachometers, potentiometers, servo drives, NC axis, stepper motors Torque range: 0,5 – 10 Nm Axial pluggable

3 measurement range from ± 0 - 0,5 Nm to± 0 - 50 Nm DRDML | DRDMS | DRDMN for mechanical connection to Maxon gearboxes with contactless data acquisition as a complete drive and torque measuring unit Test bench construction Screwing technology Supply voltage:12V DC ± 10 % Power consumption:approx. 120 mA

The RMD radiometer is one of the latest developments from Opsytec Dr. Gröbel GmbH. This easy-to-use radiometer is based on more than 30 years of experience in all areas of irradiation and illuminance measurement. It features a wide dynamic range and extremely low noise. For this purpose, the sensor already contains a multi-stage amplification, an extremely precise analog-to-digital converter and a temperature sensor. The memory contained in the sensor contains all sensor identifications and the calibration history. This allows several ultraviolet sensors and visible sensors to be used on the Radiometer RMD. A wide range of sensors is available for a wide variety of production and control processes. Two sensors can be read out simultaneously. Sensors for the evaluation of erythema-weighted radiation and multi-channel sensors are also available. The measurement data are clearly displayed on the graphic display. Spectral range:UVA, UVA+, UVBB Resolution:0,001 µW/cm² Dimensions:Ø 40 mm, h 35 mm Weight:160 g Connecting cable:2 m

Torque range from ± 0 - 0,01 Nm to ± 0 - 1500 Nm with speed or angle detection waterproof (IP67) contactless integral torque amplifier single supply voltage wide range of application small form low moment of inertia speed measurement (option) angle measurement (option) DRWPL series torque transducers are fitted with a number of gaskets in compliance with international protection IP67. The devices are also available with optional speed or angle detection for a host of applications. The integrated signal amplifier is powered with 12 V DC and outputs an electrically isolated analog signal of 0 to ± 10 V. Supply voltage:12V DC ± 10 % Power consumption:approx. 200 mA

The high-performance UV LED Solo P combines a compact, variable, and economic point light source for manual bonds in an ergonomic design. The UV LED Solo P requires no external control and can be operated directly with a mains power adapter. As all UV LEDs the Solo P is quickly switchable. WAVELENGTH, BEAM PROFILE, AND OPTIC The wavelengths of 365, 385, 395, 405, and 450 nm are available for different applications. In addition, several beam profiles with interchangeable optics are available. The UV radiation of high-power LED is focused in the desired working distance. The high irradiance of 24,000 mW/cm ² allows for short processing times. APPLICATIONS OF HIGH-POWER UV-LED SOLO P UV curing and bonding and UV sealing Micro curing Irradiation of biological samples Hairline or leak detection using fluorescence markers Wavelength:365, 385, 395, 405 or 450 nm Max. irradiance:> 24000 mW/cm² Dimensions:Ø 15 x 143 mm Weight:~130 g Operating voltage:100 - 240 V, 50/60 Hz

Customized Solution Hand-held device with integrated torque transducer. Direct channel selection of filed test programs. Drive of the transmission is achieved to the predetermined moment of friction during the assembly. Subsequent break-in period and subsequent Reibwertprüfung with threshold monitoring, visual evaluation and documentation. Direct channel selection of filed test programs Safety circuit by two-hand operation Constant load independent test speed either vertically or horizontally about Balancer

Mobile Mobile friction measurement for gear optimization 5 Nm or 30 U/min With the DPFR-036, changes in the design can be measured directly on the product. Even the smallest improvements can be identified. The area of application of this test facility is extremely diverse and can be easily implemented for other applications. The mobile design enables tests to be carried out under different temperatures and climatic conditions. Special features constant test speed independent of load selectable direction of rotation and speed Additional storage to eliminate lateral forces Acquisition of torque and angle of rotation Graphical recording of the test procedure Simultaneous viewing of up to 20 variable test sequences from the database in color Option OK and NOK signal lights

No service needed because of contactless data acquisition High accuracy due to frequency modulation and strain gage technology Single power supply High noise immunity due to amplified active signal integrated sensor-detection chip for use with GMV2 analyzer automotive industry test benches assembly applications pulsed tools hexagonal drive 7 Measurement range from ± 0 - 1 Nm up to ± 0 - 20 Nm optionally with angle measurement Supply voltage:12 V DC ± 10 % Power consumption:approx. 200 mA

verschiedene Typen von 0,02 bis 20.000 Nm lieferbar Drehmomentsensor, Drehmomentaufnehmer, Drehmomentmesswelle aus unserem Standardprogramm sowie in kundenspezifischen Variationen mit Drehzahl- bzw. Drehwinkelmessung; 27 Messbereiche von ± 0 - 0,02 Nm bis 20.000 Nm; • Montagefreundliche Befestigung mit der Option "F" / Fuß • Montageadapter erhältlich! + erweiterte EMV-Festigkeit, + einstellbarer Ausgangspegel von Drehzahl- und Winkelsignal (5 V - 24 V), + Drehmomentaufnehmer zur Messung von Drehzahl und Drehwinkel ab 0,02 Nm, + erweiteter Drehzahlbereich für Drehzahl- und Winkelmessung, + Frequenzausgang für Drehmomentsignal 10 kHz ± 5 kHz (RS422), + großer Eingangsspannungsbereich (9 - 28,8 V), + optional 0,05 % Linearitätsfehler, Messbereich: 0,02 Nm - 20.000 Nm Genauigkeit: 0,1% bzw. 0,05% Option 1: Drehzalmessung Option 2: Drehwinkelmessung

The PLC.D sensors are ready-to-install UV sensors with digital output. This enables reliable and repeatable irradiance measurements in UV systems. Due to the compact design and the eight spectral ranges, the sensors can be used for a wide range of applications, e.g. in packaging facilities sterilisation surface activation systems UV curing systems ageing tests and many other applications With the integrated 24-bit ADCs, the PLC.D sensors close the gap between industrial manufacturing and high-precision laboratory equipment. Measurements can be carried out in a simple yet safe way. RS-485 and USB are available as optional connections for this purpose. The data evaluation takes place directly in the PLC.D sensors, the measured values are protected against transmission errors by a CRC-16 check sums. Operation voltage:24 V (RS-485 / RS-232) Dimensions:80 x 40 x 20 mm Weight:150 g Connector:Built-in plug, M8, 8-pin Response time, max:200 ms

Real-time monitoring of the measurement The HawkEye software offers various forms of representation for monitoring and controlling the ongoing measurement. Any number of pages can be created in the software with different forms of presentation of the measurement data. By supporting a server-client architecture, monitoring is scalable and can be distributed across any number of PCs. •,Real-time phase analysis •,Speed signals are calculated and displayed in real time. •,Different forms of representation for the measurement signals (time domain, FFT, Bode diagram, orbit, waterfall, machine order monitoring) •,Real-time monitoring and visual representation of implemented limit values. •,Visual and acoustic signal when limit values are exceeded. •,The screen layout can be flexibly adapted to the respective monitoring requirements and user needs. •,No license fees for using the software. •,MS Windows compatible

Der BL50H ist ein hochauflösendes offenes Längenmesssystem in reflektierender Bauform Der BL50H hat eine Teilungsperiode von 1,6µm und erzeugt mit dem Laserscale Funktionsprinzip eine Signalperiode von 400nm. Die extrem kleinen Abmessungen, ermöglicht durch die reflektierende Bauform und große Montagetoleranzen ermöglichen eine einfache Integration in X/Y- Tische und verschiedenste Messanwendungen. Er liefert eine sehr hohe Signalqualität mit niedrigem Rauschlevel und eignet sich für Auflösungen von bis zu 6pm bei Verfahrgeschwindigkeiten von bis zu 3m/s Messbereich:30mm - 640mm Genauigkeit:+/-0,5µm - +/-3µm abhängig von der Ausführung Max. Verfahrgeschwindigkeit :3m/s Ausgangssignale:1Vpp, TTL, BISS-C, USB, 40bit binary Signalperiode:400nm

Digitale Positionsanzeige mit 3Kanälen für DK-Messtaster mit RS232 Schnittstelle - Zum Anschluss von bis zu drei DK-Messtastern mit Adapterkabel CE29 oder Längenmesssystemen. Standardmäßig mit RS-232C-Funktion ausgerüstet Spitzenwertfunktion, Haltefunktion Verschiedene Eingabefunktionen speziell für automatische Messungen Wählbare Anzeigeauflösung Datenspeicherung Reset/Preset/Restart Mit Referenzpunkterkennung der angeschlossenen Messeinheiten Skalierungsfunktion Kanäle:3 Kanäle für Dk-Messtaster Schnittstelle:RS232 Messfunktionen:IST/MIN/MAX/P-P Spannungsversorgung:über separates Netzteil PSC23

Xenon excimer lamps enable new, resource-saving and more efficient production possibilities. They are used in the field of surface treatment for matting, cleaning, surface activation or to save photoinitiators. For this purpose, the narrow-band spectrum around 172 nm is usually used to irradiate under inert gas conditions. Then the high photon energy is sufficient to split almost all organic compounds. The measurement of 172 nm (VUV) is an important component for process control and optimization. With the tinyTracker 172 we offer a calibrated band radiometer which is suitable for use in an inert atmosphere. The tinyTracker 172 is absolutely calibrated and measures the irradiance and irradiation dose of xenon excimer lamps directly at 172 nm. Due to its particularly flat design, the tinyTracker172 can be guided through the irradiation channels of UV belt dryers and other industrial equipment. Measuring range:0-200 mW/cm² Resolution:12 bit Recording time:up to 3 hours Sampling frequency:1 - 100 Hz, adjustable Photo detektor:GAP

Drehmomentsensor mit Zapfwellenanschluß Mit seinem robusten Design, das speziell für Feldanwendungen entwickelt wurde, ist der DRVZ ein zuverlässiger Begleiter, der selbst den anspruchsvollsten Bedingungen standhält. Dank der Schutzart IP67 ist er perfekt vor widrigen Umgebungsbedingungen geschützt, sodass Sie sich auf präzise Messungen verlassen können. Der DRVZ bietet eine umfassende Messlösung, da er nicht nur Drehmoment, sondern optional auch Drehzahl und Drehwinkel erfassen kann. Er ermöglicht außerdem noch eine genaue Lastgangmessung. Damit erhalten Sie detaillierte Informationen über den Lastverlauf Ihrer Maschinen. Insbesondere die Lastspitzenmessung ermöglicht es Ihnen, kritische Belastungsspitzen frühzeitig zu identifizieren. Die Installation des DRVZ-Sensors ist simpel und erfordert nur minimale Zeit und Aufwand. Sie können den Sensor schnell und einfach an Ihrer Zapfwelle befestigen und sofort mit der Erfassung von Daten beginnen.

With the classic network switch in Dragonfly case format, Dragonfly amplifiers can be connected bundled to a PC or to a larger network. In combination with a Dragonfly PoE (Power over Ethernet) module, this switch can be used to power Dragonfly amplifiers. •,10x 1GB/s Ethernet ports (8 ports with PoE support) •,Bundle the data streams from multiple Dragonfly amplifiers to forward them to a PC or laptop. •,Front LEDs to indicate connection and power supply via PoE.

The „Guidance document on the impact of water treatment processes on residues of active substances or their metabolites in water abstracted for the production of drinking water“ of the European Chemicals Agency (ECHA) and the European Food Safety Authority (EFSA) provides a framework for risk assessment with regard to the authorization of active substances contained in plant protection products (PPPs) and biocidal products and the approval of these products. The guidance enables the identification of actual health concerns that may arise from exposure to harmful compounds that may be formed during water treatment for drinking water production. The focus is on common water treatment methods within the European Union (EU). The UV irradiation, according to the guideline, chapter 4.2.4.6. can be realized by the BSM-03 in a reproducible way. Interior chamber:60 x 40 x 25 cm Dimensions:130 x 62 x 76 cm Weight:~ 80 kg Power consumption:1200 W Lamp lifetime:1.000 h to 3.000 h, typical

Metal Bellows Coupling with split hubs Backlash-free metal bellows coupling with compact split hubs For shaft diameters from 10 – 70 mm High torsional stiffness, compensation of shaft misalignment at low restoring forces Radial assembly! Due to the split hub design shafts can be mounted and adjusted before the assembly of the coupling Leightweight ~ space saving ~ fast assembly / disassembly Torque range: 18 – 500 Nm

Miniature Metal Bellows Coupling with split hubs Backlash-free miniature metal bellows coupling with split hubs For shaft diameters from 3 – 25 mm High torsional stiffness, compensation of shaft misalignment at low restoring forces Radial assembly! Due to the split hub design shafts can be mounted and adjusted before the assembly of the coupling Perfect bellows coupling for servo drives, e.g. in testing equipment, automation techniques, packing machines, Torque range: 0,5 – 10 Nm

For adhesive bonding and curing through UV radiation, LED spotlights and gas discharge lamps with liquid light guides, whose high irradiance enables curing and polymerization within seconds, are used. Exact measurements in order to monitor the irradiance and dose are required for the process control. Here, the UV sensor is exposed to the high irradiances and temperatures, which could lead to an impairment of the measurement results. The sensor series XT („eXtrem Temperature“) has been developed for this critical application. The XT sensors are suitable for up to 50.000 mW/cm² and operating temperatures of 150°C. At the same time, the XT sensors are compact and thus flexibly usable where needed. This is possible due to the separation of sensor-head and sensor-electronics. The XT sensor with its excellent cosine correction guides the light through a light guide into the calibrated sensor-electronic, which is integrated in the handpiece. Operation temperature:0 to 150 °C Storage temperature:-10 to 150 °C Humidity:< 80% non-condensing Light guide:0,3 m / 1,5 m Cable length:2 m