Produkty dla instrumenty (674)

The Agilent Cary 60 spectrophotometer measures the direct transmission and reflection. With the Opsytec integrating sphere you can also measure the diffuse transmission and reflection of translucent samples. Liquid and powder samples can also be measured using the extensive accessory set. Even geometries such as 0° and 8° are supported. Perfect for comprehensive material characterization! Enrich your spectrophotometric measurements with our highly reflective integrating sphere, specially developed for the Agilent Cary 60 spectrophotometer. This sphere guarantees precise, reliable and highly accurate reflectance measurements in research laboratories, quality control departments and scientific institutions. Diameter:50 mm Material:PTFE

The BS-02+ is a compact irradiation chamber for performing photostability tests according to ICH Q1B and VICH GL5 for medical products and active pharmaceutical ingredients. Irradiation is performed with UVA radiation and visible light according to option 2 of the ICH Q1B guideline. With a footprint of 46 x 32 cm and a height of up to 20 cm, the irradiation chamber provides space for samples. The sample chamber temperature during operation is approx. 25 °C, so that thermal damage to the samples is avoided. Due to the high homogeneity of the irradiation, the specimens can be positioned as desired. In accordance with the ICH Q1B guideline, modern LED light sources with a „Cool White“ emission (ISO 10977) and UVA fluorescent lamps are used. The UVA fluorescent lamps emit a maximum between 350nm and 370nm. Interior chamber:46 x 32 x 23 cm Dimensions, chamber:58 x 40 x 47 cm Weight:~ 40 kg Power consumption:250 W Mains:110 - 230 VAC, 50/60 Hz

The UV measuring probes with 14 mm diameter only serve as compact, long-term, stable measuring heads for the supervision of UV irradiation systems and for UV measurements in inaccessible locations. In addition, optional water and light guide adapters enable the application in hot locations and in water disinfection systems. The integrated electronics generate a signal voltage that is transferred to the UV monitor RM-31 or to the PLC with low noise by a shielded cable.

The UV LED chamber BSL-03 is the second largest irradiation chamber in the BSL series. The high irradiance combined with the exact dose control offers a unique reproducibility for perfect results! Due to the irradiance of up to 220 mW/cm², it is possible to use the most common UV curing adhesives or lacquers. For high irradiances, the UV LED chamber can be ordered completely with one LED wavelength. A particularly flexible application is possible when two separately controllable LED wavelengths are ordered. Compared with our irradiation chambers of the BS series, the BSL-03 offers an irradiance that is 22 times as high. The high irradiance allows for extremely short exposure times. With the high homogeneity of the irradiation, the samples can also be positioned as needed. Due to the typical characteristics for UV LEDs, such as “immediate start”, the dimmability and the high durability, the BSL-03 is ideally suited for medium-sized laboratory tests and curing of large components. Interior chamber:68 x 51 x 31 cm Sliding sample carrier:64 x 49 cm Dimensions:77 x 64 x 68 cm Weight:~ 70 kg Power consumption:1000 - 2000 W Mains:100 - 240 V, 50/60 Hz Operation temperature:10 to 40 °C Storage temperature:-10 to 60 °C Cooling:air cooling

High UV irradiance combined with a uniform irradiated area is the key feature of the surface LED series SFL-UV. The SFL-UV modules are water-cooled high-power UV LED sources with an intelligent LED driver. The absence of ineffective infrared radiation reduces the heat compared to conventional UV lamps. Three standard sizes are available with light-emitting areas of 100 x 100 mm to 200 x 200 mm. Customized sizes are available on request. Independent of size, we offer two versions. The HO versions reach high irradiance of up to 5500 mW/cm², while the ECO versions still offer up to 2000 mW/cm². Both irradiances are measured at a distance of 10 mm to the emitting window. The high irradiance allows extremely short processing times. Wavelengths of 365, 385, 395, 405, and 450 nm are available for many different applications. Wavelength:365, 385, 395, 405 or 450 nm Connections:Trigger in, dimming in (0-10V) Programming, optional:RS485, RS232 or USB Internal security circuit:Over-temperature, LED N.C. Optical feedback, opt.:internal and external sensor

Lesekopf zum Anschluß an Positionsanzeigen LG20 und LH70 Serie Ausgangssignal: TTL A/B Quadratur-Signal, konform mit EIA-422 Maximale Auflösung: 10μm Maximale Ansprechgeschwindigkeit: 300m/min (variiert je nach Lesekopf und Einstellung) Extrem unempfindlich selbst bei rauesten Umgebungsbedingungen (IP65) Resistent gegenüber Öl, Staub, Vibration und Schock Auflösung:10µm Ausgangssignal:TTL Linedriver RS422 Spannungsversorgung :5V DC Max. Ansprechgeschwindigkeit :5m/s Zum Anschluß an Positionsanzeigen :LG20, LH70, LY70- Serien Kompatible mit Längenmesssystem:SL110 oder SL130

The UVpad is the world‘s thinnest spectral measuring and autonomous UV radiometer. It combines scientific measurement technology with a compact and user-friendly instrument. With its innovative measuring principle, it doesn't use optical filters. UV light is spectrally detected and analyzed in the UVpad. Thus, measurements are traceable to national standards. Since it works without a filter, it is particularly suitable for the measurement and comparison of different lamps. All measurement data are displayed on the device immediately; 50 measurements are stored in the UVpad and can be read via USB. The supplied PC software evaluates the irradiance intensity profiles measured separately for UVA, UVB, UVC, and VIS. Spectrum and measurement data can be exported and saved. Optionally, UV systems can be optimized due to saved operating functions such as, for example, the absorption spectra of photo initiators. Thus, the operation costs can be reduced and the product quality can be ensured. Dimensions:160 x 100 x 14,4 mm³ Weight:~ 375 g Operation temperature:10 -70 °C Battery:internal LiIon accu Memory:50 measurements

The UVpad E combines the benefits of the spectral measuring technology with a handheld and easy to operate radiometer. The UVpad E is technically based on our successful radiometer UVpad. With the external sensor and an optimized programming, it is even more precise and easier to operate. Use the spectroradiometer UVpad E for an accurate measurement of the UV irradiance and for comparisons of different UV lamps and UV LEDs. 512 photodiodes measure the spectrum in the wavelength range of 240 – 480 nm. The categorization in UVA, UVB and UVC is taken according to international standards and traceable. The calibration to only one light source is omitted. Spectral range:240 - 480 nm ± 5 nm Spectral bandwidth:2 nm Pixel distance:~0,5 nm Irradiance meas. range (typ.):2 - 5000 mW/cm² Irradiance meas. range (high power version):25 - 20000 mW/cm²

Der neue DMS-Verstärker mit IO-Link-Schnittstelle ermöglicht eine Digitalisierung der Messtechnik direkt ab dem Sensor. Durch die kompakte Bauform und hohe Schutzklasse kann der Messverstärker nahezu überall im Feld eingesetzt werden. Typische Ausgangsspannung von DMS-Sensoren ist wenige Millivolt. Im industriellen Umfeld, z.B. in der Nähe von Elektromotoren oder Frequenzumformern, können bei der Übertragung von analogen Signalen Störungen das Messergebnis beeinflussen. Dies wird mit dem neuen DMS-Verstärker mit IO-Link-Schnittstelle zuverlässig vermieden. Die analoge Verbindung zwischen Sensor und Messverstärker wird möglichst kurz gehalten, die standardisierte IO-Link-Kommunikation arbeitet voll digital und störungssicher. Die Spannungsversorgung des Verstärkers erfolgt direkt über die IO-Link-Schnittstelle – ein standardisiertes 5-poliges Kabel mit M12-Buchse. DMS-Sensoren können über einen 4-poligen M8-Stecker angeschlossen werden. Schnittstellen:IO-Link Messrate:1000 Werte pro Sekunde Sensortyp:DMS Schutzart:IP65 Versorgungsspannung:über standardisierte IO-Link-Schnittstelle Anschlüsse:M8 4-polig (Sensor), M12 5-polig (IO-Link)

FEATURES: Bereit für Ihre Sensoren (DMS, Poti, Prozesssignal analog ±10 V, Inkrementell), herstellerunabhängig Blitz-Konfiguration über Tasten Automatische Sensorerkennung durch burster TEDS Feldbusanbindung über Feldbus-Controller erweiterbar Unterstützt in Kombination mit dem Feldbus-Controller 9251 ethernetbasierende Feldbusse wie PROFINET, EtherCAT, EtherNet/lP Bis zu 8 Messverstärker an einen Feldbus-Controller kaskadierbar Alle Messdaten auslesbar Abbildbare Messgrößen sind Kraft, Druck, Weg, Drehzahl und Drehmoment (auch in Kombination) Tariermöglichkeit über Taste oder über E/A-Signale pro Messverstärker 9250 Bis zu zwei Echtzeitsignale/Grenzwertschalter pro Verstärkermodul Flexible Konfiguration über PC-Software DigiVision via USB-Schnittstelle Alle Konfigurationsdaten editierbar Hohe Messgenauigkeit Platzsparend im Schaltschrank Variabel einstellbare Grenzfrequenzen Linearitätsabweichung:< 0,005 % v.E. Messrate:14400 Mess./s. Sensortyp:DMS / Potentiometer / DC/DC/Inkrementelle Sensoren Schnittstellen:Schraubklemmen Sensorspeisung-DMS-Vollbrücke::2,5 V / 5 V / 10 V konfigurierbar, kurzschlussfest Sensorspeisung-Potentiometer::5 V Schutzart:IP20 Versorgungsspannung:11 ... 30 V DC. Galvanische Trennung, Verpolschutz,Überspannungsschutz

40 years of UV experience and consistent product development enable the optimal performance and intuitive operation of the RMD Touch laboratory radiometer. This incorporates the latest technologies such as capacitive touch displays, precision ADCs, data storage, remote update capability and much more. This makes the RMD Touch one of the most powerful multichannel radiometers on the market with superior features such as highest accuracy, reliability and modular extensions. The RMD Touch allows simultaneous measurement of multiple sensors, recording of irradiance and dose. Each sensor channel contains a high-precision 24 bit ADC and a multi-stage amplification to achieve a wide dynamic range of up to 7 orders of magnitude. The measurement of all channels is performed simultaneously. Sensor spec:24 bit, full digital Sensor connections:2 Display:capacitive touch display Dimensions:185 x 251 x 100 mm Mains connection:100 - 240 V, 50/60 Hz

We would be happy to check the dimensional accuracy of your components in-house. LT Ultra-Precision Technology has a large number of high-precision measuring devices in precisely air-conditioned measuring laboratories for testing its own products, on which we also carry out contract measurements.The following measurement technology is available:High-precision coordinate measuring technology.Interferometric shape measurement technology for plane surfaces, spheres and aspheres.Roughness measurement technology via white light interferometer (WLI) or atomic force microscope (AFM).Reflections- and Transmissionsmessung.Ellipsometrie.Polarimetrie

Customized Solution The mobile testing device may be mounted directly on the wheel nuts on any wheel on the car. The height and tilt adjustment allows optimal orientation at the wheel. Additionally, it is still supported by three proximity sensors. The evaluation and control of the testing device accepts a laptop. For easy transport, the device can be disassembled in a few steps. Curve recording and analysis via notebook. The complete unit is height adjustable via a scissors system. This can also be adapted to different shaft height.

The mains-driven panel meter RM-32 provides a continuous and precise measurement of irradiance with preamplified UV sensors. The integrated electronics produce a signal voltage that is transmitted to the radiometer, so that inferences are minimized. Different UV and visible spectral ranges, measuring ranges, and output signals can be selected to match the measurement task. The current irradiance is shown on a 3.5-digit digital display. The lamp state with respect to two threshold values is indicated by LEDs. Two relay contacts can be used for switching warning and failure signals. With its optional USB, RS232 or RS485 interface the RM-32 can be used to monitor ultraviolet (UV) irradiance. Control of light sources and irradiation systems Precise measurement of irradiances UV monitor for process control and documentation Dimensions:DIN 43700 96 x 48 mm Depth:~ 115 mm Weight:410 g Mains:230 V, 50 Hz, 3 W Operating temperature:0 to 40 °C

Der RESISTOMAT® Typ 2329 ist besonders für die schnelle Messung niederohmiger Widerstände in der Automation geeignet. Bis zu 50 Messungen pro Sekunde sind problemlos realisierbar. Das Gerät entspricht den neuesten CE-Richtlinien und ist für den Laborbetrieb wie auch für den harten industriellen Einsatz ausgelegt. Für Klassifizierungen und Selektierungen steht ein 2- und 4- fach-Komparator mit Schaltausgängen zur Verfügung, was besonders für Reihenuntersuchungen vorteilhaft ist. Typische Einsatzgebiete sind Widerstands- und Leitfähigkeitsmessungen an: — Schmelzsicherungen — Airbag-Zündern — Magnetspulen für die Kfz- und Elektroindustrie — Steckkontakten und Schaltern — Kommutator-Schweißverbindungen — Meterproben in der Kabelindustrie — Leiterbahnen und dergleichen mehr Messbereiche:200,00 Ω, 2,0000 , 20,000 Ω, 200,00 Ω, 2,0000 kΩ, 20,000 kΩ, 200,00 kΩ Auflösung:10 μΩ, 100 μΩ, 1 mΩ,10 mΩ, 100 mΩ, 1 Ω, 10 Ω Messgenauigkeit:≤ 0,03 % v.M. Anzeigeumfang:20 000 Digits Automatische Temperatur-Kompensation:Ja Komparator:Ja Schnittstellen:RS232, SPS, IEEE488 (optional), USB (optional) Ethernet (optional)

The SM71 series force sensors were specially developed for measuring clamping forces. The short measuring path of 0.019 - 0.14 mm (depending on the measuring range) and a natural frequency in the kHz range guarantee optimal results even for highly dynamic tasks. Typical applications include the simple determination of screw preloads, where the force sensor is used as a “measuring washer”. The very good reproducibility is less than one percent of the nominal load. The sensor is available in measuring ranges from 20 up to 2000 kN. Hardened washers are already included in the scope of delivery for quick and easy installation. The extremely simple and robust design is made entirely of stainless steel (protection class IP68).

The BS-03 is a medium-sized, rugged irradiation chamber for time- or dose-controlled irradiation of samples with UVA, UVB, or UVC. The chamber can be fully equipped for one of the spectral ranges UVC, UVB, or UVA to achieve the highest irradiance. Alternately, the use of two separately controlled lamp groups for different spectral ranges allows for especially flexible operation of the chamber. The interior irradiation chamber has a base area of 68 x 49 cm² and a height of 32 cm. The sliding sample carrier facilitates loading and unloading. With a load of up to 20 kg, this can withstand all demands. The sample chamber operating temperature is about 25°C so that thermal damage to the specimen is avoided. Due to the high uniformity of the irradiation, the samples may be positioned in any order. Two irradiation controls are available for the BS-03: the UV-MAT and the UV-MAT Touch. Interior chamber:68 x 49 x 32 cm Dimensions:77 x 64 x 68 cm Power consumption:300 W Lamp lifetime UVA:up to 4.000 h Lamp lifetime UVB:up to 4.000 h Lamp lifetime UVC:up to 9.000 h Irradiance UVA:8 mW/cm² Irradiance UVB:2.4 mW/cm² Irradiance UVC:10 mW/cm²

The HP-120i is a high-intensity short arc light source for quick UV spot curing within seconds. As a microprocessor controlled spotlight source with light guide, HP-120i is a reliable and economical „cold“ light source for irradiation with high-intensity UV-A radiation and blue light. The heat transfer in the material is minimized due to the absence of ineffective red and near-infrared radiation. The spotlight source uses fiber-optic cables in various configurations for flexible irradiation of one to four points. Depending on the light guide, UV-A irradiances of up to 15,000 mW/cm² can be achieved. The exposure time can be set through a digital timer with a resolution of 0.1 s. The shutter can also be switched by a foot switch or via a PLC system controller by an external contact. The typical lamp life is 2,000 hours. To achieve uniform irradiation, the lamp power is stabilized. Lamp lifetime:2000 h (typical) Dimensions:305 mm x 358 mm x 145 mm Weight:~ 8,2 kg Mains:110 - 230 VAC, 50/60 Hz Operation temperature:5 to 40 °C

Series DRDL torque transducers are suitable for lab and industrial applications because of their small size and multiple mounting options. As supply voltage and output signal are transmitted without contact, the device can operate continuously with low wear and no maintenance. These transducers are also available with optional speed and angular measurement for a host of applications. The integrated signal amplifier is powered with 12 V DC and outputs an electrically isolated analog signal of 0 to ± 10 V per torque range. Simultaneous measurement of peak torque and operating torque Torquesensor with speed or angle measurement High accuracy with 100% overload protection 16 measurement range from ± 0 - 0,5 Nm up to ± 0 - 5000 Nm 2 torque ranges (1/10 - 1/2 of the 1st measuring range) Integral signal amplifier Low moment of inertia Single supply voltage Wide range of applications Multipurpose use Contactless output signals Compact Speed measurement (option) Angular measurement (option) Supply voltage:12V DC ± 10 % Power consumption:approx. 200 mA

Mobile test device for detection of the maximum torque (drag indicator mode) and for the detection of the power range (constant load) of motors in dental and dental surgical application area. arbitrary loading curves endurance test speed ​​measurement in aluminum case permanently installed Calibration disc and calibration will be in the trunk.

The water-proof sensor UVX-SE serves as robust, long-term stable measuring heads for the precise measurement of UV irradiances in production lines, that have to be wet cleaned. The sensors are calibrated with traceability to the PTB (Physikalisch Technische Bundesanstalt, the German national test authority) and can be exposed to pressure of up to 10 bar. The sensors are available in eight spectral ranges and two measuring ranges. This allows the sensors to be optimally adapted for the application. The integrated electronics produce a signal that is transmitted to the PLC or panel meter, so that inferences are minimized. Operating voltage and output signal can be selected to match the measurement task or PLC interfaces. For small control tasks, the sensor UVX-SE can be connected to RM-32, which shows current irradiance on a 3.5-digit digital display and switches two relay contacts with adjustable warning and alarm signals. Measuring range:0 - 200 mW/cm² Measuring range option:0 - 20 mW/cm² Connector:G 3/4“ Dimensions:see drawing Weight:~420 g

Bourdon takes mechanical pressure monitoring into the digital age This innovative device fits to any comprehensive platform for machine and process monitoring as well as the preventive maintenance of equipment which is supported by a LoRa wireless protocol. Key applications include pressure measurement and monitoring for oil refineries, petrochemical industry and biodiesel plants. More predestined applications are in waste and water treatment, power generation and transmission, general process industry, building services and civil engineering. The right choice when industry grade wireless pressure measurement and monitoring is required

Die Messdaten des Messtaster können über Ethernet, EtherNet/IP, PROFINET oder EtherCAT Feldbus an eine SPS gesendet werden Feldbuskompatibles Interfacemodul: MG80-NE (Ethernet) / MG80-EI (EtherNet/IP) / MG80-PN (PROFINET) / MG80-EC (EtherCAT) An jedes Hauptmodul können bis zu 16 Zählermodule MG80-CM für Messtaster angeschlossen werden An MG80-NE können über max. 3 LINK-Verbindungen bis zu 64 MG80-CM bzw. Messtaster angeschlossen werden An MG80-EI/PN können über LINK-Verbindungen bis zu 255 MG80-CM bzw. Mestaster angeschlossen werden An MG80-EC können theoretisch über LINK-Verbindungen bis zu 65.535 MG80-CM bzw. Mestaster angeschlossen werden MG80-CM Zählermodul zum Anschluss von einem Messtaster der Serie DK oder DT (mit MT13) Einfache Installation auf DIN-Montageschiene LZ80-K1/K2 E/A Modul für MG80-EI, MG80-PN und MG80-EC Ausgestattet mit 8 Eingängen und 8 Ausgängen Interfacemodule für :Ethernet ; Ethernet/IP ; PROFINET; ETHERCAT Kompatible Messtaster :DK-Serie und DT-Serie mit MT13 Adapter

Series DRVL torque transducers are suitable for lab and industrial applications because of their small size and multiple mounting options. As supply voltage and output signal are transmitted without contact, the device can operate continuously with low wear and no maintenance. These transducers are also available with optional speed and angular measurement for a host of applications. The integrated signal amplifier is powered with 10 - 28,8 V DC and outputs an electrically isolated analog signals of 0 ± 10 V and 10 kHz ± 5 kHz. The standard version has smooth shaft ends, several types are available with optional keyways

Calibrate and adjust mechanical yarn brakes for the textile industry The test specimen is inserted in the UUT, which is mounted on a pneumatic slide. By pressing a button, the candidate moves to the running belt drive. The sample is then tested in different locking positions, the switching of the individual Paramtersätze is realized via a rotary switch. In each latching position, IO / NIO statement about the GMV2 light mounted on the column is displayed visually. After passing the examination, the tray will open again and the next candidate can be inserted. A speed controller as well as an ON / OFF switch for the drive are also integrated in the switch box under the GMV2. The entire inspection unit is mobile and complained to a height-adjustable lifting unit. The GMV2 and connect the switch are also mounted height adjustable in the profiles.

The very high irradiances of up to 39,000 mW/cm² and the compact dimensions characterize the UV-LED Spots and allow extremely short process times. For this purpose, the UV-LED is focused at the desired working distance. The UV-LED Spot P is suitable for automated and manual bonding. For applications such as bonding, potting or fluorescence excitation, the wavelengths 365, 385, 395, 405 and 450 nm are available. With the variety of wavelengths as well as the exchangeable optics, you remain particularly flexible and can upgrade and change over at any time. For controlling the UV-LED Spot P, we offer the LedControl S as a table top device or the LedControl DC for DIN rail mounting. With the LedControl S and DC UV LED controllers, the ultraviolet LED output can be set between 2% and 100%. Wavelength:365, 385, 395, 405 o. 450 nm Dimensions, Spot P:Ø 15 x 143 mm Dimensions, Spot P short:Ø 15 x 60 mm Cable length:1,5 m Weight:~130 g

Miniature Metal Bellows Coupling axial pluggable, with collet clamps Backlash-free miniature metal bellows coupling with clamp hubs For shaft diameter from 3 – 25 mm High torsional stiffness, compensation of shaft misalignment at low restoring forces Easy assembly with friction-locked clamp hubs Perfect bellows coupling for encoders, tachometers, potentiometers, servo drives, NC axis, stepper motors Torque range: 0,5 – 10 Nm Axial pluggable

3 measurement range from ± 0 - 0,5 Nm to± 0 - 50 Nm DRDML | DRDMS | DRDMN for mechanical connection to Maxon gearboxes with contactless data acquisition as a complete drive and torque measuring unit Test bench construction Screwing technology Supply voltage:12V DC ± 10 % Power consumption:approx. 120 mA

Der Spatel für Lebensmittel SteriPlast® aus blauem Polystyrol wird in unserem Reinraum Klasse 7 (10.000) produziert, für den Einweg-Bedarf einzeln verpackt und anschließend gammastrahlensterilisiert. Durch den langen, ergonomisch geformten, stabilen Handgriff und eine spitze Klinge, ist es möglich selbst mit diesem Einwegprodukt direkt in Gebinde wie Papier- oder Kunststoffsäcke einzustechen. Der Spatel für Lebensmittel ist ideal für die Probenahme von Pulver, Granulaten und Pasten. Der blaue Farbton kommt in natürlicher Form in Lebensmitteln nicht vor. Deswegen werden die blauen Produkte, oder Teile davon, falls sie einmal in die Produktion geraten sollten, bei der visuellen Kontrolle sehr schnell und leicht erkennbar und auffindbar sein. Die Verwendung von blauen Werkzeugen hilft somit den Anforderungen der HACCP Gefahrenanalyse und -bewertung in Bezug auf Fremdkörper zu entsprechen. Besonders in der Lebensmittelverarbeitung, Lebensmittelproduktion, sowie in der Futtermittel- und Material:PS blau

The RMD radiometer is one of the latest developments from Opsytec Dr. Gröbel GmbH. This easy-to-use radiometer is based on more than 30 years of experience in all areas of irradiation and illuminance measurement. It features a wide dynamic range and extremely low noise. For this purpose, the sensor already contains a multi-stage amplification, an extremely precise analog-to-digital converter and a temperature sensor. The memory contained in the sensor contains all sensor identifications and the calibration history. This allows several ultraviolet sensors and visible sensors to be used on the Radiometer RMD. A wide range of sensors is available for a wide variety of production and control processes. Two sensors can be read out simultaneously. Sensors for the evaluation of erythema-weighted radiation and multi-channel sensors are also available. The measurement data are clearly displayed on the graphic display. Spectral range:UVA, UVA+, UVBB Resolution:0,001 µW/cm² Dimensions:Ø 40 mm, h 35 mm Weight:160 g Connecting cable:2 m