Produkty dla instrumenty (291)

Approved flue gas velocity CEM for stack velocity, volumetric flow and pollutant mass release calculations when linked to gas and dust CEMS. Measured parameters:Flue-gas velocity Technology:FlueSonic™ Ultrasonic Measurement/Monitoring capability:0 – 50 m/s Stack/Duct diameter suitability:up to 10 m Flue gas temperature:up to 200 °C Baghouse:Yes Cartridge Filter:Yes Coalescent Filter:Yes Cyclone:Yes Electrostatic Precipitator (ESP):Yes Wet Electrostatic Precipitator (WESP):Yes Wet Scrubber:Yes QA checks:Yes

Referenz-Luftqualitäts-Überwachungssystem für CO-Messungen im Bereich 0-50 ppm. Optional kann CO2 überwacht werden. Messgröße:CO Technologie:Gasfilter-Korrelation – NDIR QAL 1 Zertifizierung:Ja US-EPA Zulassung:Ja Messbereiche:0-50 ppm (0-300 ppm auf Anfrage) Messeinheiten:ppb, ppm, µg/m3 (benutzerdefiniert) Untere Nachweisgrenze (2σ):0.05 ppm Rauschen (σ):0.025 ppm

The Cairsens© O2 + NO3 sensor allows specific pollutant measurement comparable to reference methods. Measured Parameter:O3 + NO2 Measuring Range (ppm):0 – 0.25 Certified Detection Limit (ppm):0.02 Resolution (ppm):0.001 Operating Temperature (°C):-20 to 40

Ultra-fast NH3 measurement (Ultra-fast response time: < 2 seconds). Ranges:0-100 / 0-500 ppm Lower detectable limit:0.4 ppm Response time:< 2 sec (T90) Zero drift:< 2% F.S. / 24 h Span drift:2 % F.S. / 24 h Linearity :± 1 % F.S. Sample flow rate:0.1 to 5 l/min Heated block temperature :190°C Operating temperature :+5 to +45°C Communication:RS 232

Ideal für mittelhohe bis hohe Konzentrationen, auch in explosionsgefährdeten Bereichen und zur Verwendung mit AC32e, CO12e, AF22e, HC51M oder MIR 9000. Temperaturbereich Standard:+ 400 °C Temperaturbereich Quartzsonde:+ 600 °C Verdünnungsrate:12/1 bis 350/1 Genauigkeit der Verdünnungsrate:± 2 %

Gaschromatographie in Verbindung mit einem Photoionisationsdetektor zur Messung von organischen Verbindungen wie Benzol, Toluol, Ethylbenzol, m+p-Xylol, o-Xylol, 1-3 Butadien. Messbare Parameter:VOC (Benzene, Toluene, Ethylbenzene, m+p-Xylene, o-Xylene, 1,3 Butadiene) Technologie:Gaschromatographie QAL1-Zertifikat:Ja US-EPA Zulassung:Ja Messbereich:0-1000 µg/m3 Messeinheit:ppb, ppm, µg/m3 (frei wählbar) Nachweisgrenze (2σ):≤ 0.025% µg/m3 at 0.5 µg/m3 benzene Rauschen (σ):≤ 0.5%

Sensor for continuous moisture measurement in dry bulk solids and installation on conveyor belts, screw feeder or hoppers. Microwave based sensor for high resolution and accuracy. • highly resistant to abrasion • extended measurement range, up to 85 % moisture • high temperature version up to 190 °C • measurement accuracy 0.1 % • recording of surface moisture and capillary moisture

QAL1 approved ProScatter™ particulate CEM providing high quality emission measurement of low dust concentrations from dry industrial processes. Measured parameters:Dust Technology:ProScatter™ Forward Scatter Measurement/Monitoring capability:0-1000 mg/m³ Stack/Duct diameter suitability:up to 8m Flue gas temperature:up to 500°C Baghouse:Yes Cartridge Filter:Yes Ceramic Filter:Yes Coalescent Filter:Yes Cyclone:Yes Electrostatic Precipitator (ESP):Yes

Filter leak monitor suited to filter control applications after fabric dust filter type (baghouse) arrestment plant. Measured parameters:Dust Technology:Electrodynamic™ Probe Electrification Measurement/Monitoring capability:0-500 mg/m3 (Leak monitoring) Stack/Duct diameter suitability:0.5 to 8 m Flue gas temperature:250°C standard, 400°C option Baghouse:Yes Cartridge Filter:Yes Ceramic Filter:Yes Coalescent Filter:Yes Cyclone:Yes

Microwave sensor for contactless monitoring of material flows with trend monitoring. • detection of material clogging and material standstill • insensitive against material deposits • for any line diameter • compact (no separate electronics) • with ceramic mounting, usable up to 1,000 °C • usable in dust exzones

US EPA PS11 capable ProScatter™ particulate CEM for the extractive sampling and measurement of particulate in saturated wet gas streams. Measured parameters:Dust Technology:Extractive ProScatter™ Forward Scatter Measurement/Monitoring capability:0-500 mg/m³ Stack/Duct diameter suitability:up to 15m Flue gas temperature:up to 200°C Wet Electrostatic Precipitator (WESP):Yes Wet Scrubber:Yes QA checks:Yes

Standard Reference CLD method for low & ultra low NOx measurement, IRGFC for CO, CO2, SO2, N2O, NOx, HF, HCl, TOC and O2 in a single analyse. Fast and simultaneous measurements of up to 10 gases. • measurement of dry and corrosive samples • unheated sample line • intrinsic security with onboard residual H2O measurements • onboard oxygen measure for environmental reporting • highly accurate, excellent stability with automatic optical stability check

Vermeidet durch die Verwendung des UV-Bereichs für die Messung von NH3 Interferenzen mit anderen wichtigen Emissionsgasen (CO, CO2, H2O, usw..), die im UV nicht absorbieren. Messbereich:0-100 / 0-500 ppm Nachweisgrenze:0.4 ppm Reaktionszeit:< 2 sec (T90) Null-Drift:< 2% F.S. / 24 h Messbereichs-Drift:2 % F.S. / 24 h Linearität:± 1 % F.S. Ultraschnelle Reaktionszeit:< 2 Sekunden

Multigas-Infrarot-Analysator für Messungen niedriger CO-Konzentrationen (0-10 bis 0-50 ppm). Messbereich:CO: 10 bis 50,000 ppm, CO2: 100 bis 250,000 ppm, O2: 0 bis 25%v Reaktionszeit (0-90 %):2 sek. Temperaturbereich :+15°C bis + 40°C

QAL1 zertifizierte Emissionsmessung für Staubkonzentrationen aus industriellen Prozessen mit einem Zertifizierungsbereich von 0-7,5 mg/m³. Messbare Parameter:Staub Technologie:ProScatter Rückwärtsstreuung Messbereich:<0 – 500 mg/m³ Eignung für Durchmesser:bis zu 10 m Rauchgastemperatur:bis zu 400 °C Taschenfilter:Ja Kartuschenfilter:Ja Zyklone:Ja Elektrofilter (ESP):Ja

The ProSens has been specially developed to carry out reliable dust measurement on clean sides after filters. The measuring device provides measurement values for dust concentration, either as a trend signal or as absolute values (after calibration) for emission measurement. • continuous, precise and reliable dust quantity measurement (mg/m³) • dust measurement possible in large channel diameters • output of dust concentration as absolute value • ATEXcertified • measurement of dust concentration at high temperatures or harsh environments • trend signal or absolute value

Mikro-Sensor für die präzise und zuverlässige Messung von nmVOC. Messbarer Parameter:nmVOC Messbereich:0 – 2 | 0 – 16 Zertifizierte Nachweisgrenze (ppm):0.2 | 0.5 Auflösung (ppm):0.001

The MGC101 system automatically performs zero, precision, span and multi-point calibrations using NO, NO2, SO2, CO, 03, hydrocarbons and other gases.

QAL 1 certified for continuous, accurate and reliable measurement of total mercury emissions, even in very low concentrations and within complex matrices (SO2, NOx, HCl, etc.). Measuring principle:Thermocatalytic reduction at stack, Amalgamation (MI GoldTrap), cold vapor atomic absorption (CVAAS) Measured component:Total mercury UV-Source:Electrodeless low pressure mercury lamp (EDL) Stabilization method:Reference beam method Measuring ranges:0.05 μg/m³ – 500 μg/m³ Hg (up to 1000 µg/m³ as an option) Detection limit:0.0001 μg/m³ (Detector); < 0.01 μg/m³ (System)

LED based, UV photometric ozone analyzer providing accurate, stable and repeatable O3 measurements in the range of 0-500 ppb or 0-10 ppm. Measured parameter:O₃ Technology:UV photometry & LED US-EPA Approval / QAL 1 Certification:Yes Measurement ranges:0-1 ppm / 0-10 ppm Measurement units:ppb, ppm, µg/m3 (user-selectable) Lower Detectable Limit (2σ):0.2 ppb Noise (σ):0.1 ppb Zero drift:< 0.5 ppb / 24h, < 1 ppb / 7 days Span drift:< 0.5% / 24h, < 1% / 7days Linearity:± 1% FS Sample flow rate:1L/min

This accessory is meant for manually calibrating the UT-3000 Mercury Ultratracer. Purity of contained Hg:99,999999% Accuracy of T-sensor:0,01 °C Power supply:230 VAC / 50 Hz (110 VAC / 60 Hz option) Power consumption:30 VA

Continuous particulate monitoring for saturated wet stack applications typically found after wet scrubbers, wet electrostatic precipitators and wet flue gas desulphurisation plants. Measured parameters:Dust Technology:Extractive ProScatter™ Forward Scatter Measurement/Monitoring capability:0-500 mg/m³ Stack/Duct diameter suitability:up to 15m Flue gas temperature:up to 200°C Wet Electrostatic Precipitator (WESP):Yes Wet Scrubber :Yes

Standalone TÜV approved filter dust monitor suited to the measurement of filter emissions after bag houses, cartridge filters, cyclones etc. • reliable measurement of leaking and broken bags in dust collectors • external display and keyboard • inbuilt sensor drift checks • probe check option for improved data integrity • reduces filter maintenance intervals, process downtime and filter costs

Beta Messgerät mit optionalem OPM (Optischer Partikelsensor). Präzises Messgerät zur Überwachung der Beta-Dämpfung von PM10, PM2,5, PM1. Optische Echtzeit-Anzeige der Massenkonzentration unter Verwendung eines unabhängigen Einlasses. Messbare Parameter:PM10, PM2.5, PM1, TSP Technologie:Beta-Strahlen-Dämpfung QAL1 Zertifizierung:Ja US-EPA Zulassung:Ja Messbereich:bis zu 10 000 μg/m3 Messbare Einheit:µg/m3

Messung von Kohlenwasserstoffen (THC, CH4, nmHC) in der Umgebungsluft unter Verwendung eines Flammenionisationsdetektors (FID). Messbare Parameter:THC / nmHC Technologie:Flammenionisationsdetektor (FID) Messbereiche:0-10 ppm / 0-1000 ppm Messeinheiten:ppb, ppm, µg/m3 (frei wählbar) Nachweisgrenze (2σ):< 0.05 ppm Rauschen (σ):0.025 ppm

The Cairsens© sensor allows specific pollutant measurement comparable to reference methods. Measured Parameter:nmVOC Measuring Range (ppm):0 – 2 | 0 – 16 Certified Detection Limit (ppm):0.2 | 0.5 Resolution (ppm):0.001 Operating Temperature (°C):-20 to 50

The MMS basically comprises a multiplexer-valve unit and a highly accurate and selective mercury detector (VM-3000 Vapor Monitor) for measurements in air and other gases. Measuring principle:cold vapor atomic absorption (CVAAS) at 253.7 nm UV-Source:Electrodeless low pressure mercury lamp (EDL) Stabilization method:Reference beam method Optical cell:Fused silica (Suprasil), l: approx. 230mm, heated approx. 45° Measured component :Total Gaseous Mercury (TGM) Measuring ranges (Standard version):1 – 100; 1- 1000; 1 – 2000 µg / m³

Microwave barrier for contactless detection of dry bulk solids in containers, pipes or chutes. Reliable fill level and limit detection. • simple retrofitting • detection through all nonconductive walls • up to 1,000 °C possible with ceramic mounting • insensitive to material caking • usable for profiles up to 25 m

Flue gas flowmeter for continuous measurement of gas velocity, temperature and pressure in exhaust gas ducts (chimneys or flue pipes). Measured parameters:Flue-gas velocity Technology:Micro-venturi Measurement/Monitoring capability:3 – 30 m/s Stack/Duct diameter suitability:300 mm up to 1,5 m Flue gas temperature: up to 400 °C Baghouse:Yes Cartridge Filter:Yes Ceramic Filter:Yes Coalescent Filter:Yes Cyclone:Yes Electrostatic Precipitator (ESP):Yes Wet Electrostatic Precipitator (WESP):Yes

PM162M is a sequential automatic sampling device for particulate matter in the ambient air. The particles are sampled at constant flow rate (1 m3/h or 2.3 m3/h) and collected on filters for gravimetric weighing and possible physicochemical laboratory analysis. Measured parameter:Particulates Technology:Sampling Temperature range:+5°C to +40°C Data storage:> 6 months Included I/O:4 AI/4 AO/4 RC/6 DC