Produkty dla instrumenty (3700)

1 or 2 channel multifunctional display for DT series probes. Perfectly suited for quick and easy measured value evaluation in assembly and production plants. The display has a comparator function with switching outputs for connection to the PLC for fast pass/fail evaluation. The displays can be easily installed in the front panel Measuring modes: ACTUAL, MAX, MIN, P_P Addition and subtraction function: A+B, A-B Comparison function: setting of upper/lower limits; GO / NO GO via NPN open collector output Start/hold function Channels:1 or 2 for gauges of DK-series Resolution:0,1µm / 0,5µm / 1µm / 5µm Measuring functions:Current/MAX/MIN/P-P Axis calculation:ADD/SUB Comparator function:High/Go/Low by Open collector I/O Interface:I/O with NPN Open collector; Optional: RS232 or BCD Power supply:9-26 V DC Dimensions for Front panel mounting:72mm x 72mm

Non,sterile, autoclavable, sterilizable by gas (Ethylene oxide) 24 cm sponge holder. Thanks to its superrior lock it's not easy to open while holding code:M12110201 Size:24 cm Package Dimensions:47 cm x 31 cm x 47 cm Package Quantity:600 Package Weight (kgs):13,20 Color:Blue

No service needed because of contactless data acquisition High accuracy due to frequency modulation and strain gage technology Single power supply High noise immunity due to amplified active signal integrated sensor-detection chip for use with GMV2 analyzer automotive industry test benches assembly applications pulsed tools hexagonal drive 7 Measurement range from ± 0 - 1 Nm up to ± 0 - 20 Nm optionally with angle measurement Supply voltage:12 V DC ± 10 % Power consumption:approx. 200 mA

The PLC.D sensors are ready-to-install UV sensors with digital output. This enables reliable and repeatable irradiance measurements in UV systems. Due to the compact design and the eight spectral ranges, the sensors can be used for a wide range of applications, e.g. in packaging facilities sterilisation surface activation systems UV curing systems ageing tests and many other applications With the integrated 24-bit ADCs, the PLC.D sensors close the gap between industrial manufacturing and high-precision laboratory equipment. Measurements can be carried out in a simple yet safe way. RS-485 and USB are available as optional connections for this purpose. The data evaluation takes place directly in the PLC.D sensors, the measured values are protected against transmission errors by a CRC-16 check sums. Operation voltage:24 V (RS-485 / RS-232) Dimensions:80 x 40 x 20 mm Weight:150 g Connector:Built-in plug, M8, 8-pin Response time, max:200 ms

Mercury emission monitoring by sorbent traps is a good and practical alternative to conventional Hg CEMS. Measuring range: (total mercury) :0.01 – 1000μg/m3 Sampling period::from 15 minutes up to 4 weeks Flue gas temperature::< 200˚C with heated probe; > 200˚C on request Max. dust concentration in flue gas::20 mg/m3 Operating temperature::+5 to +40˚C (optional with air conditioner: -20 to + 55˚C)

3D printing or additive manufacturing (AM) is any of various processes for making a three-dimensional object of almost any shapes. At RPWORLD, additive manufacturing 3D printing is designed for functional prototypes, complex designs, and production components. - Materials selection Selective laser sintering, (SLS), Stereolithography (SLA) and Fused Deposition Modeling (FDM) are the most common additives manufacturing processes that RPWORLD uses to realize a project. - Cost-efficiently You can get the 3D printed parts of any possible shapes as you desire. And more importantly, since it doesn’t need the mold, it could be a cost-effective process for your custom parts. - Complex-geometries The structure of the 3D printed parts is not limited, you can nearly get any shapes as your part design. Industries Applied:Medical Device Industries Applied:Scientific Instrument

Vaso de plástico, PP, muy transparente, dispositivo de medición, equipo de labo - Vaso de laboratorio basado en la norma DIN EN ISO 3819 (vidrio, antes DIN 12331), versátil. En pedidos grandes es posible una impresión individual. Material:PP altamente transparente

Features: — nominal pressure: 0 ... 100 mbar up to 0 ... 6 bar — accuracy: 0.5 % FSO — stainless steel sensor without media isolation

The LPX low-pressure calibrator is a high-precision calibration instrument for pressures between -0,85 bar and 10 bar (after taring to ambient pressure). The functional calibrator is supplied in a sturdy carrying case and pressure can be quickly generated manually. It is therefore ideal for use in the field. The pressure is measured by the integrated LEX1 manometer and output both on the display and via the RS485 interface. Additional functions such as zero point resetting, peak and trough pressure value indication and leak measurement make it even easier to take measurements. Pressure Ranges:-0,85…10 bar Accuracy:0,05 %FS Interfaces:RS485 Display:5-digit LCD display Special characteristics:For air pressure

The new 9250/9251 amplifier generation unites all the features that make modern measurement data acquisition actually possible for the first time. Network-compatible, high-precision, user-friendly, smart and versatile: the combined system of amplifier module and bus controller can be integrated into any existing setup. The amplifier 9250 in conjuction with the fieldbus controller 9251 takes signals exactly to the point where they can be combined, monitored and linked efficiently to other data. The fieldbus interfaces give you flexibility, speed and perfect connections, and save you time, money and other resources when integrating your measurement setup with existing systems. Automatic sensor recognition due to burster TEDS lets you play absolutely safe, protecting you from setting incorrect parameters. The broad supply voltage range permits operation on standard power supplies used in switch gear cabinets. Non-linearity:< 0,005 % F.S. Sample rate:14400 Meas./s. Type of sensor:Strain gage / Potentiometer / DC/DC / Incremental sensors Interfaces:Screw terminal Sensor excitation:2,5/ 5 /10 V /configurable, Sensor excitation:Strain gage full bridge:V = 2,5 5,10, configurable,short-circuit proof Sensor excitation:Potentiometer: 5 V Protection class:IP20

Wraz z rodziną produktów Combics Minebea Intec oferuje wysokiej jakości serię wag do różnych zastosowań w przemyśle spożywczym, farmaceutycznym, chemicznym, metalowym i elektrycznym. Combics może optymalnie dostosować się do różnych wymogów procesowych dzięki swojej dużej elastyczności w odniesieniu do opcji połączeń i konfiguracji. Dostępne są trzy wersje terminali wraz z programami aplikacji i interfejsami.

Knight Optical can offer IR-cut filters for use in Heat Shielding. We supply a range of Custom and Stock IR-cut filters for a range of applications. All individually QA checked and metrology tested for quality to ensure parts meet customer specification. Supplied in a range of sizes and shapes with custom coatings tailored to meet your individual applications. Knight Optical supply precision optical components to customers with Heat Shielding requirements. Our IR-cut filters allow good transmission levels of visible light but cut off IR and UV radiation. Our precision grade filters have an AR coating to increase their visible transmission. In many systems that require heat shielding while still needing visibility an IR-cut filter can be used. These can attenuate infrared radiation and allow through visible light, allows your temperature sensitive equipment For more information read the PDF…… Material::Borosilicate Dimensional Tolerances::±0.2 Transmission::Tavg>90% 420-620nm (Standard Grade) Transmission::Tavg>94% 420-620nm (Standard Grade) Blocking::Tmax<2% 700-1000nm Wavelength Accuracy: :±10nm Surface Accuracy:60/40 (Standard Grade) Surface quality::60/40 (Standard Grade)

The CryLaS Q-series lasers are diode-pumped solid-state lasers (DPSS lasers) based on a microchip design. It consists of a Nd:YAG resonator with a directly coupled saturable absorber that works as a passive Q-switch. The compact housing and simple operation make the lasers an ideal light source for applications that require minimal housing dimensions with maximum performance. Based on the 1064 nm fundamental, non-linear optics (NLO optics) generate frequency multiples of this fundamental, covering a broad spectrum of laser wavelengths from 1064 nm to 213 nm. The FQSS266-Q2 laser emits pulses with a pulse width of approx. 1 ns at 266 nm and can be modulated from single shot to 10 kHz. The pulse energy is 0.8 µJ. CryLaS lasers impress with their simple installation, service-free operation and long service life. This makes them ideal for OEM applications and demanding laboratory setups. Wavelength:266 nm Pulse energy:0.8 µJ Peakpower:0.8 kW Pulse Width:1 ns Average Power:8 mW Repetition Rate:10 kHz Beam diameter:0.8 mm Spatial Mode:TEM00 Application:Holography, engraving, photo acoustics, LIBS, mass spectroscopy, photo luminescence

Annular compression load cells. o Low profile for highcapacity load cells Sturdy design Reference:5190-5195 Material:stainless steel (5190) or nickel-plated steel (5195) Protection class:IP65 Cable length:see drawing table - CL (other lengths available on request) Repeatability error (% F.S.*):<± 0.25 Creep error over 30 min. (% F.S.*):<± 0.3 Zero shift after loading (% F.S.*):<± 0.5 Reference temperature (°C):23 Compensated temperature range (°C):-10...+45 Service temperature range (°C):-30...+70 Storage temperature range (°C):-50...+85 Temperature coefficient of the sensitivity (% F.S.*/10°C):< ± 0.2 Temperature coefficient of zero signal (% F.S.*/10°C):<± 0.2 Nominal sensitivity (mV/V):1.5 Input resistance (ohm(s)):700 ± 2 Output resistance (ohm(s)):700 ± 2 Insulation resistance (50 V) (Mohm(s)):> 5000 Reference excitation voltage (VDC):10 Permissible nominal range of excitation voltage (VDC):3...12 Safe load limit (% F.S.*):150 Breaking load (% F.S.*):> 300 Permissible dynamic loading (% F.S.*):50 Zero balance (mV/V):± 0.02 Static lateral force limit (% F.S.*):25

Transmetteur de niveau radar (FMCW) pour les solides : des granulés jusqu'aux roches L'OPTIWAVE 6400 est un transmetteur de niveau radar (FMCW) 2 fils 24 GHz pour les solides des granulés aux roches. Ce radar est destiné à mesurer le niveau, la distance et le volume des poudres, granulés, roches, céréales et tout autres types de solides dans diverses industries. Le transmetteur de niveau est disponible avec une antenne conique métallique ou une antenne Drop PP et PTFE. La conception éprouvée de l'antenne Drop permet de minimiser la formation de dépôts et n'est pas affectée par l'angle du talus. Fluide::de liquide Technologie::radar FMCW Affichage::numérique Plage de mesure::0…100 m / 328 ft Température::Jusqu'à +130°C / +266°F Pression::16 barg / 232 psig

L’afficheur de couple Magtrol modèle 3411 est conçu pour une utilisation avec les couplemètres Magtrol TS, TM, TMHS, TMB et TF. Facile à utiliser, il alimente le couplemètre et traite les signaux à haute vitesse, pour afficher le couple, la vitesse de rotation et la puissance mécanique. L’afficheur 3411 peut aussi être utilisé avec tous types de couplemètres alimentés sous 24 V DC (500 mA max) avec une sortie couple de ± 5 V DC (± 10 V DC max.) et une sortie vitesse en collecteur ouvert, TTL ou CMOS. Sélection de l’unité:Anglaise, Metrique et SI

The Raytek MP150 infrared linescanner is designed for temperature monitoring in demanding industrial environments. It generates accurate thermal images of moving objects, scanning up to 90° wide fields of view with a motorized mirror at up to 1024 points per line and at a max. 150 Hz frequency. An internal high-speed microprocessor calculates the temperature of the individual measurement points. — Real-time thermal line-scanner system for continuous or discrete process measurements — Optical resolution up to 200:1 — Built-in line laser for rapid alignment — On-board Ethernet TCP/IP communication — Wide choice of models and spectral responses The Raytek MP150 includes provision for air or water-cooling, three configurable analog outputs, and two-way digital communications. It can be used in standalone mode, connected to a single PC or integrated into a process control system using the Windows-based DataTemp DP software for remote configuration and real-time process monitoring. Measured temperature range:20 °C...1200 °C (dependent on model) (up to 3000°C option on request) Spectral range:1 µm...5 µm (dependent on model) Scan rate:Up to 150 lines per second Measurement points per line:Up to 1024 Optical resolution:Up to 200:1 Interfaces:Ethernet TCP/IP (100 Mbit/s), OPC, DDE, analog/digital output, RS485 Ingress protection:IP65 (NEMA4) (rugged enclosure with air-purge and built-in water cooling capability) Ambient temperature:Up to 180 °C Scanning angle:90° Power supply:24 VDC ± 25 %, 1 A

Enregistreur de données climatiques avec une technologie de mesure extensible Le DL200P permet l'intégration simultanée de deux paires d'électrodes pour mesurer l'humidité de résistance et de deux capteurs de température externes TS910. C'est pourquoi, le DL200P peut être utilisé pour de nombreuses autres applications de surveillance, par exemple pour surveiller un silo, contrôler les matières en vrac ou contrôler la température de liquides à base d’eau. Par ailleurs, les rapports du DL200P pour un assèchement de chantier ou après un dégât des eaux permet de livrer une documentation complète aux assurances ou fournit une protection contre les demandes de recours. La fonction d’alarme est pratique, elle permet de détecter et donc d’éviter d’éventuels dommages au niveau de la structure de bâtiments et de l’ameublement. Grandeur mesurée:de température Connectique:USB Affichage:avec écran Applications:non spécifié Autres caractéristiques:programmable,robuste

GM8802S-T weighing indicators are specially designed for weighing industrial fields, which have features of small volume, plenty of communicating commands, stable performance, easy operation, and practicability.

The EQM-402 Mixer Mill is a great ally when preparing samples for analysis, as it can mill, mix and homogenize quickly small volumes of sample. Especially designed for the final preparation of small quantities of hard, semi-hard and fragile samples - up to 50 ml -. This unit is able to prepare two samples simultaneously and to reduce them from an initial size of 0.8 a 1.5mm to a grain size of less than 10μ in a short time – 1 to 4 minutes -.

medidores de agua, Semi-racores, sellos, reducciones y extensiones de medidores de agua.

Vis sur mesure usinage.

Das EBATmètre® ist ein Gerät zur Messung von Mehrkaliber-Höhenspielen (Messung der Luft). Es wird hauptsächlich verwendet, um das Spiel der beweglichen Teile eines mechanischen Uhrwerks zu messen.

— es adecuado para todos los productos a granel de flujo libre — diseño compacto que ahorra espacio Más opciones: — diseño a prueba de explosiones Rango de potencia - diferente versiones 2000 - 4000 dm³/h 3000 - 100000 dm³/h 10000 - 160000 dm³/h

Herstellung von Gasdorsiersystemen für Reinstgase

Messvorrichtung für die Ermittlung der Schnittkraft von Schneidklingen ▪ Messprinzip: Kraftmesssensor in Schnittrichtung verfahrbar mit Servogetriebemotor ▪ Manuell bedienbar unter individuellen Versuchsbedingungen ▪ Automatische Wasserbenetzung und Einzug des Schnittmaterials aus Vorratskassette ▪ Schnellwechselvorrichtung für verschiedene Klingentypen ▪ Vergleichsmessung von Schnitt zu Schnitt, Kraft-Weg-Diagramm ▪ Sonderausführung auch als kleines Tischgerät mit manueller Bedienung und Momentanwert-Kraftanzeige (ohne Datenarchivierung) Made in: Germany

Wir entwickeln, konstruieren und bauen jede von Ihnen gewünschte Vorrichtung. Hierzu gehören z.B. manuelle, halbautomatische oder vollautomatische Dichtheitsprüfvorrichtungen, Montagevorrichtungen, Nietvorrichtungen, Schweißvorrichtungen, Messvorrichtungen oder Fügevorrichtungen. Sollten Sie Vorrichtungen nach Ihren eigenen Konstruktionen bei uns bauen lassen wollen, so ist dies auch jederzeit möglich.

programmierbar, LED-Display rot, 1x20-Segmente 1x3-stellige LED-Anzeige rot, Eingänge DC Strom/Spannung, Einbaugehäuse 96x24mm

Unlock the power of component analysis with Sciospec's LCR-1! Electrical component analysis has never been easier. Based on the same technology as our industry leading impedance analyzers the LCR-1 combines next-level performance with the simplicity of an LCR meter. In terms of range, accuracy and speed the LCR-1 sees eye to eye with competing high-end devices while maintaining a compact formfactor, simple setup and ease of use previously unseen in this class.

Mit einer Kugel aus Rubin und einem Schaft aus Hartmetall garantiert der Sterntaster von dk präzises Messen im µ-Bereich. dk bietet ein lagerhaltiges Standard-Programm von weiteren 3D-Messtastern. Komplettes System von Tastereinsätzen für Koordinatenmessmaschinen in verschiedenen Größen, Ausführungen, Materialien und Geometrien für individuelle Mess-Anforderungen. Auch kundenspezifische Sonderlösungen mit Zubehör kurzfristig und zum günstigen Preis lieferbar. Herkunftsland:Deutschland Standardgrößen:M2 - M5