Produkty dla instrumenty (9550)

Urethane casting is a fast and cost-effective method of producing small series from a silicone mold. A silicone mold is made with the help of a prototype which serves as the basis for the duplication process of the original piece. Thanks to the flexibility of the silicone, complex intermeshing geometries can be achieved without demoulding problems. The base material used for the reproductions is a liquid polyurethane resin which with the use of additives can simulate the properties of a wide variety of plastics. Between 15 and 30 parts can be produced depending on the requirements of the material and surface finish. This method is ideal for the production of small batches and prototypes in which the production of expensive injection molding tools is not feasible. Industries Applied:Medical Device Industries Applied:Scientific Instrument

Ultra-fast NH3 measurement (Ultra-fast response time: < 2 seconds). Ranges:0-100 / 0-500 ppm Lower detectable limit:0.4 ppm Response time:< 2 sec (T90) Zero drift:< 2% F.S. / 24 h Span drift:2 % F.S. / 24 h Linearity :± 1 % F.S. Sample flow rate:0.1 to 5 l/min Heated block temperature :190°C Operating temperature :+5 to +45°C Communication:RS 232

The precision screw-in transmitter LMP 331i demonstrate the further development of our industrial pressure transmitters. The signal processing of sensor signal is done by digital electronics with 16-bit analog digital converter. Consequently it is possible to conduct an active compensation and the transmitters with excellent maesurements and exeptionally attractive price to offer on the market. Features — nominal pressure: 0 ... 400 mbar up to 0 ... 40 bar — accuracy: 0.1 % FSO — thermal error in compensated range -20 … 80 °C: 0.2 % FSO TC 0.02 % FSO / 10 K — turn-down 1:10 — communication interface for adjusting of offset, span and damping Optional Features — IS-version Ex ia = intrinsically safe for gases and dusts — adjustment of nominal pressure gauges (factory-provided)

Bote de envasado de diseño moderno con tapa de rosca. Vaciado sin restos, ya que no existen ranuras, económico. Material:PP blanco Esterilizable:sí

LT10A, LT11A Unités d'affichage pour la série DT afficheur multifonction à 1 ou 2 canaux pour les jauges numériques des séries DT Modes de mesure : Valeur courante, MAX, MIN, P_P Fonction d'addition et de soustraction : A+B, A-B Fonction de comparaison : réglage des limites supérieure et inférieure ; GO / NO GO via une sortie collecteur ouvert NPN Fonction Start/Hold Interface : BCD / RS232 (en option) Alimentation électrique : 9 à 26.4 VDC Nombre de canaux:1 ou 2 Mode de mesure:Valeur courante, MAX, MIN, P_P Fonction d'addition et de soustraction:A+B, A-B Interface:BCD / RS232 (en option) fonction:Start/Hold Fonction de comparaison:réglage des limites supérieure et inférieure ; GO / NO GO via une sortie collecteur ouvert NPN

The MPX pressure calibrator is a high-precision calibration instrument for pressures between -0,85 bar and 25 bar (after taring to ambient pressure). The functional calibrator is supplied in a sturdy carrying case and pressure can be quickly generated manually. It is therefore ideal for use in the field. The pressure is measured by the integrated LEX1 manometer and is both shown on the display and output via the RS485 interface. Additional functions such as zero point resetting, peak and trough pressure value indication and leak measurement make it even easier to take measurements. Pressure Ranges:-0,85…25 bar Accuracy:0,05 %FS Interfaces:RS485 Display:5-digit LCD display Special characteristics:For air pressure

The SENSORMASTER 9163 covers a wide range of applications in which process values need to be measured, displayed, analyzed and transferred to higher-level control systems. Typical applications include measuring geometric values in production, for instance differential measurements, or testing material properties in the laboratory. The measured values can be transferred via USB, RS232 or analog output. Features: — For force, pressure or torque measurements using strain gauge sensors — For position or angle measurement using potentiometric or DC/DC sensors — For temperature measurement using Pt 100 sensors or thermocouples — Optional multi-channel model — Optional Profibus or serial interface — 0.1 % measurement accuracy plus sensor-specific linearization — Range of mathematical functions (e.g. differential measurement) — OK/NOK feedback on multi color display and via 4 alarm limit outputs — High sampling rate (500/sec.) Measurement accuracy:0.1 % F.S. Sample rate:500/s Interfaces:RS232, RS485, USB Indicator:5 digit, dual-color red/green Sensor excitation Strain gauge::5 / 10 V / 60 mA Sensor excitation Potentiometer::2,5 / 5 / 10 V Standard signal, DC/DC::± 60 mV, ±100 mV, ±1 V, ± 5 V, ± 10 V Sensor excitation Transmitter::15/24 V / max. 150 mA Protection class:IP20 Supply voltage:100 - 240 VAC / 50 - 60 Hz Measurement channels:16

Gehäuse und messstoffberührte Bauteile im Hygienic Design SIP und CIP geeignet Klemmverbindung zur Reinigung und Dichtungswechsel schnell lösbar Einfache Nullpunkteinstellung

Der HSZ-CP050 Adapter ist aus anodisiertem Aluminium gefertigt und hat eine eingebaute Reduktionslinse 0,5x um ein besseres Sichtfeld im Huvitz Trinolukular-Tubus zu erreichen. Dieser Adapter ist speziell entwickelt für die Huvitz-Mikroskope Serie HRM und HSZ: Er passt insbesondere für CMOS / CCD Sensoren der Größe 1/1.8", 1/2" und 1/2.5". Bitte achten Sie daher auf die Sensorgröße Ihrer vorhandenen Kamera, bzw. wählen Sie den passenden Adapter, wenn Sie eine unserer C-Mount-Kameras bestellen möchten.

Boitier : GS55 80 x 80 mm Protection mécanique IP65 Protection capteur IP65 Principe de mesure par résistance piste plastique amplifiée Plage de température -20 > +50°C Poids 800 gr. Article numéro 5929Z55-264.021 Plage de mesure:15 000 mm Précision:IP65

rounded corners

z.B. als Zuckerportionierer, ohne Graduierung, nicht stapelbar Farbe nach Wunsch mit CE-Kennzeichen Abmessung:L= 130 mm, B= 34,9 mm, H= 34,5 mm Artikelnummer:7259 Herkunft:Deutschland Material:ABS

The DRV8872DDAR is a full and half-bridge driver IC from Texas Instruments. It is designed to drive DC motors with up to 3.6A of continuous current. It is housed in an 8-pin SOIC package and is capable of operating from a wide range of supply voltages, from 4.5V to 36V. The DRV8872DDAR features a wide range of protection features, including over-current protection, over-temperature protection, and under-voltage lockout. Kynix Part #:KY32-DRV8872DDAR Manufacturer Part #:DRV8872DDAR Product Category:Full, Half-Bridge Drivers Manufacturer:Texas Instruments Package:8-PowerSOIC (0.154, 3.90mm Width) Quantity:6045 PCS Lead Time:3(168 Hours)

Low-noise coaxial measuring cables are used wherever the smallest voltages or charges have to be reliably measured, e.g. in pH measurement technology or nuclear research. The method was developed by bda connectivity and ensures reproducible results. Depending on the requirements, these cables can be supplemented with supply or power supply wires as well as additional shields. Type:MXR 0,45L/1,4 Product Number:3309 Purpose of use:Measurement technology / low-noise version Jacket material:PVC Country of origin:Germany

The Beagle™ I2C / SPI analyser from Total Phase is probably one of the best known I2C/SPI analysers on the market and is used by many worldwide electronics companies. It has been designed specifically for developing I2C, SPI, or MDIO based products. This small and portable analyser delivers high-performance monitoring solution of bus signals and is an ideal companion for engineers working in the field or in the lab.

-Ürünlerin sınıflandırması. -Dakikada 100 ürün etiketlenebilir. -Dinamik kalibrasyon. -Metal dedektör (opsiyon). -X-Ray (opsiyon). -3 renkli sinyal ışığı. -Rüzgar kapağı. -Ayrıca Checkweigher olarak kullanabilir. -Yerinde yükseklik ayarı mevcuttur. -Feedback mevcuttur. -Raporlama yapılabilir. -Uzaktan erişim. -Kolay kalibrasyon. -Otomatik sıfırlama (resetleme)

The tensiometers of the DCAT series are measuring instruments for force-based investigation of surface and interface properties. Because of the compact and modular product design of the DCAT series, a bespoke combination of device and accessories can be found for any use case. The DCAT 15 is the standard model of the DCAT series and offers more measurement methods and modular extensions compared to the entry-level models. In addition to measuring surface and interfacial tension as well as density, the DCAT 15 can be used to determine dynamic contact angles, the surface energy of solids and to investigate sedimentation and penetration properties. Together with the LDU 25 liquid dosing unit, automatic concentration series can be generated to determine the critical micelle formation concentration. Measurements: - surface and interfacial tension - liquid and solid density - dynamic contact angles - surface energy of solids - determination of the critical micelle concentration (CMC)

In addition to supporting Waters innovative LC portfolio, we also partner with a variety of instrument vendors to provide you with the versatility you need for your business. To that end, Waters partners collaboratively with a variety of chromatographic instrument vendors to provide a robust approach for multi-vendor instrument control in Empower in order to provide a wide array of choices to enable business flexibility and productivity. Elevate Your Lab Click here to learn more about how to Elevate Your Lab with Waters LC solutions like our new MaxPeak Premier Solutions. Partner drivers for Empower are developed utilizing a Waters-created standard approach called Open Interface Portal (OIP). Waters provides our partners with the knowledge and information required to develop drivers for Empower, including guidance and support for the OIP approach. IEEE-controlled instrument support is no longer offered in Empower, click here to learn more.

The industry standard for the highest hygienic checkweigher demands with unpacked foodstuffs The CWPmaxx hygienic checkweigher series has a particularly robust construction; it is ideally suited for use in the most difficult industrial wet cleaning environments. The hygienic design particularly required in the production areas within the food industry is exemplary. The CWPmaxx hygienic checkweigher weighs and checks unpack-aged products or open packages. The CWPmaxx is used where intensive wet cleaning occurs and high IP69 protection is required. The open design facilitates easy cleaning and minimises product build up and deposits. CWPmaxx hygienic checkweigher process scales are not only sturdy enough for high-pressure wet cleaning, but they were designed to meet the strict hygienic design requirements of the European Hygienic Engineering and Design Group (EHEDG): ergonomic, providing the maximum safety for unpack-aged foodstuffs with minimal structural components. Additionally...

Guitare électrique 4 micros et surtout bonne guitare pour débutant et pour le rock

Le MEB de table PHENOM ProX est le système ultime tout-en-un d’imagerie et d’analyse par rayonnements X. Le ProX permet d’étudier en même temps la structure physique de l’échantillon et d’en déterminer la composition chimique grâce à son détecteur EDS spécifique. L’EDS est une technique qui utilise les rayonnements X générés par un faisceau d’électrons sur un échantillon. L’analyse d’éléments EDS est entièrement intégrée au PHENOM ProX et combinée en un seul module avec le détecteur de rayonnements X et le logiciel de commande. Le logiciel d’identification d’éléments (EID) peut être utilisé pour l’analyse d’un ou de plusieurs zones afin d’identifier les éventuelles contaminations sur un échantillon. En outre, les performances de ce logiciel peuvent être étendues au moyen d’un logiciel de cartographie d’éléments ou de balayage pour l’identification des éléments. MEB de table polyvalent avec analyseur EDS intégré pour l’identification chimique des éléments:Tension d’accélération : 5kV, 10kV et 15kV Plage de grossissement de 20 x à 350 000 x:Modes vide poussé et vide dégradé Résolution < 8 nm (BSED) et < 6 nm (SED):Facilité d’utilisation grâce aux réglages automatiques

75 button chromatic Bandoneon 150 reeds (2 reeds per note) 18- fold bellows with 2 central frames black or mahogany varnished with finish bespoke reed arrangement on demand

Standardinduktoren und Sonderanfertigungen Induktoren für alle Standardbauteile sind in der Härterei Rieker vorhanden. Dadurch können die meisten Arbeitsaufträge schnell und zuverlässig ausgeführt werden. Benötigen wir einen Sonderinduktor so fertigen wir diesen in unserem eigenen Werkzeugbau an. Dadurch sind wir in der Lage uns kurzfristig und flexibel auf die gegebenen Werkstückgeometrien Ihrer Bauteile einzustellen.

Ein Bauprojekt beginnt mit der Planungsphase. Anhand der Kundenvorgaben erstellen wir eine 3D Konstruktion. So sieht der Kunde die von ihm gewünschte Anlage in realisitischer Darstellung - you get what you see. Wir arbeiten dabei hauptsächlich mit Solid Works. So können wir dem Kunden maßgeschneiderte Lösungen anbieten.

Extremely sharp instruments for cutting and dessecting gums. They are useful in cutting sutures and bandages too. Blades have different designs depending on the type of operation to be performed, they often have saw edges to hold tissues during cutting.

Günther GmbH Temperaturmesstechnik | Thermoelemente

Neu entwickelter Leuchtenkopf mit superschmalem Linsenrand für verbesserten Zugang zum Objekt

Prüfung mittels Massestromverfahren - Mehrkanalanwendungen möglich - Verschiedene Messbereiche möglich - Elektronischer Druckregler - Komplett fernsteuerbar - Optional über ProfiNet fernsteuerbar

Ideal für Glasleisten, Zierleisten und Verkleidungen. Die Präzisionsdoppelgehrungssäge DS2750 eignet sich besonders zum genauen Sägen kleiner Querschnitte aus Holz, PVC und Aluminium. unkaputtbare Doppelgehrungssäge (ca. 900 kg Maschinengewicht bei 250er Sägeblatt) stabile Stahlkonstruktion Positionierung des Sägeaggregates und der Sägevorschub über 25er bzw. 20er Linearführungen optimale Absaugeigenschaften durch Abblasvorrichtung und Späneführung innerhalb der Säge Klemmung der Schwenkung bzw. der Längsbewegung über pneumatische Klemmelemente der Firma Zimmer Gegenlager im Sägetisch sorgt für optimale Stabilität und Präzision alle Antriebe und Steuerungen aus dem Hause Jetter IP 65 geschützter 15 Zoll Industrie Touch Panel WEGOMA eigene Software auf Kundenbedürfnisse anpassbar über Jahrzehnte bewährte kombinierte Spannung vor allem für Holzglasleisten

Als NI-Alliance Partner nutzen wir NI-TestStand und NI-LabVIEW für die Testautomation. Python, C/C++ Embedded und Microsoft PowerBI können ergänzend eingesetzt werden. NI-TestStand ist die Industriestandard Test-Management Software und wird von den Entwicklern und Architecten bei Merecs Engineering mit viel Erfahrung eingesetzt. Wir bieten bspw. folgende Leistungen an: - Anforderungsanalyse auf Basis der zu prüfenden DUT-Eigenschaften - Erarbeitung von Testfällen in Kooperation - Sequenzentwicklung in TestStand - Intuitive Custom User Interfaces - Paralleles Testen vieler DUTs - Reporting (SQL-Datenbanken uvm.) - Schulungen & Workshops Unsere Entwickler verfügen über die Zertifikate CLA (Certified TestStand Architect) und CLD (Certified TestStand Developer).