Produkty dla nie (9)

Sanazieg Adhesive high breathability and moldability mortar, based on hydraulic lime, for filling the vanishing points between elements in stone, brick, mouldings, decorative articles etc., in ecological building interventions, new buildings and in the restoration of vintage buildings and monuments. It can be added with earth colours, ornamental aggregates etc. Sanazieg is a product consisting of hydraulic lime, botticino, kaolin, calcium caseinate, Vichy salt, tartaric acid, ammonium salts and natural fibres. It has high hygroscopicity and breathability, contains no cements, resins, solvents and radioemissive substances. Jointing and filling interstices between bricks, or between bricks and stones, in mouldings, and in decorative articles, etc., in interventions of restoration and rehabilitation of old buildings and buildings of historical interest. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface". Pour about 2/3 of the mixing water into the mixer. Gradually add Sanazieg and the water still required, continue to mix until a homogeneous, lump-free mixture of the desired consistency is obtained. The mixing water indicatively necessary is equal to 14%-16% by weight (3.5 - 4 litres per 25 kg bag). Apply with trowel, mechanical plastering machine, etc., in the interstices prepared as specified. To highlight the aggregate, use a sponge or a wet brush as soon as the plaster Sanazieg begins to harden. For more significant removals, spray retardant solutions like PRERIT, immediately after spreading. Approximately 1.6 kg of Sanazieg for each cubic decimetre of volume to be filled (on average 10-15 kg/m² of solid brick masonry to fill). Bag 25 kg - Pallet: 50 x (Bag 25 kg)

A cura di Simone Spiazzi L’Adunanza Plenaria del Consiglio di Stato, con sentenza n. 16 dell’11 ottobre 2023, si è pronunciata, in particolare, sulla natura dell’illecito edilizio consistente nell’inottemperanza all’ordine di demolizione sanzionato dall’art. 31 del T.U. edilizia e sull’applicabilità o meno della sanzione pecuniaria prevista dall’art. 31, comma 4-bis, T.U. edilizia, alle ordinanze di demolizione emesse prima dell’entrata in vigore della norma. La pronuncia approfondisce poi ulteriori aspetti del procedimento di repressione degli abusi edilizi, altrettanto rilevanti, ma che non verranno trattati nel presente contributo. 1. La vicenda La vicenda trae origine da un’ordinanza di demolizione notificata il 4.4.2014 con cui un Comune aveva ordinato al proprietario di demolire una serie di opere abusive realizzate nel fondo di sua proprietà, ricevuto in donazione dall’autore degli abusi. L’ordinanza è stata impugnata innanzi al T.A.R.

iPhone 12 mini 64GB Used Mobile Phone US version Original Refuirbished, No any scratches, Like Brand New

Idee brillanti per trasmettere il cuore e l'anima della tua attività. Emoziona il tuo pubblico, catturane l’attenzione, stregalo con il tuo fascino.

Start up di progetto; Risk Assessment & Gap Analysis in accordo con UNI ISO 31000 Gestione del rischio Principi e linee guida e Sistemi di Gestione Anticorruzione ISO 37001; Definizione del Modello Organizzativo di Gestione e Controllo conforme al D.Lgs. 231/2001 e definizione delle procedure o parti speciali; Corso di formazione alla Direzione e alle figure apicali coinvolte nel sistema di gestione; Audit Interno. RISULTATO PREVISTO Attestazione di Consulenza Integrata che la Società ha adottato, attuato ed implementato un Sistema di Aziendale conforme alla "Disciplina della responsabilità amministrativa delle persone giuridiche, delle società e delle associazioni anche prive di personalità giuridica". MANTENIMENTO ed IMPLEMENTAZIONE del SG231 Revisione Documentale Audit e Riesame del Sistema di Gestione 231 • Adeguamento a fronte di eventuali novità legislative o modifiche organizzative • Eventuale Revisione Documentale a fronte di ulteriori esigenze o necessi

Sanatigh This macroporous, breathable, dehumidifying, fibre-reinforced plaster, with a base of natural hydraulic lime NHL 3.5, is for the dehumidification and hygrometric restoration of buildings and masonry, in works on green buildings, for new constructions and in the restoration of historic and monumental buildings. Sanatigh is a product consisting of hydraulic lime, botticino, kaolin, very fine calcium, expanded lightweight aggregates of volcanic origin, fiber-reinforced with special glass microfibres and fibers Readymesh PM 060. It has high hygroscopicity and breathability, contains no cements, resins, solvents and radioemissive substances. It has strong dehumidifying capacities and, thanks to the total absence of cement, is perfectly compatible with all types of masonry and especially with the historical walls and in all the interventions designed according to the canons of green building. Breathable dehumidifying plastering for wall bodies. Removal of crumbling plaster, if present, up to a maximum height of about 1 metre, with respect to the line of persistent humidity; wall bodies of application must in any case be clean, intact, dust-free, fouling, crumbling and non-adhering parts, conveniently saturated with water until they reach the condition of "saturated with dry surface". In the presence of salt efflorescence it will be necessary to ensure it is carefully removed by applying packs of the specific detergent and saline converter Deterg-A, in solution with water of 1:4. To prevent any new spills of salts, use specific universal anti-saline treatments in aqueous solution, Sanareg, for humid surfaces, or solvent-based, FEST SALZ, for cohesive saline concretions but with perfectly dry surfaces. PREPARATION OF THE WALL SURFACE • Remove all inconsistent, friable and rotten material, and grouting from joints, paying utmost attention where they are particularly friable or inconsistent (see also the paragraph on PREPARING SUPPORTS). • In case of strong salt concentrations, read the paragraph on PREPARING SUPPORTS. ROUGH COAT The sprayed rough coat must create a rough, corrugated surface to facilitate the adhesion of the following plaster, which must be applied promptly; within 1 - 2 days from the application of the rough coat. This adhesion spray must be applied with a low thickness (of a few millimetres) using a plastic-fluid consistency, and can be applied with the same Sanatigh product mixed with about 20% water. In case of particularly deteriorated masonry, it is recommended to use a specific Untersana product to make the rough coat. PLASTER The following application of Sanatigh must be made before the complete hardening of the rough coat (within 24-48 hours if the rough coat is made with Sanatigh, and 12-24 hours if made with Untersana). Put about 2/3 of the mixing water into the mixer, and then gradually add Sanatigh and the remaining water, continuing to mix into a homogeneous, lump-free mixture of the desired consistency for trowel or plastering machine application. Indicatively, the necessary mixing water is 16-18% by weight (i.e. 4 - 4.5 litres per 25 kg bag). Application can be performed by manual (trowel, plastering trowel) or mechanical spray methods. In case of application with a plastering machine, in order to allow adequate and homogeneous product mixing, it is recommended to not use machines with a continuous cycle, and to adjust nozzle, air and spray power in order to softly and lightly apply the product without excessive compaction. SKIMMING Levelling of plastered surfaces with Sanastof: green-construction fine, highly breathable mortar, natural hydraulic lime based with special, light, spherical micro-aggregates and high strength microfiber Readymesh PM 060. Protect surfaces from fresh direct exposure to sunlight, from the rain and wind. Cure the prolonged moist hardening. For thicknesses in excess of the 2 cm, and to improve the anti-cracking potential, provide for inserting a suitable reinforcement plaster-holding mesh: ARMAGLASS 140 o, recommended, a galvanized steel wire mesh with 2mm diameter, mesh 5x5 cm. Approximately 13 kg/m² of Sanatigh for every centimetre of thickness to be implemented (minimum thickness 2 cm = 26 kg/m²). Bag 25 kg - Pallet: 50 x (Bag 25 kg)

Untersana With the addition of mixing water only, this single-component premix creates a breathable, dehumidifying rough coating, preparatory to the application of restorative, dehumidifying, thermal-insulating and anti-condensation plasters, specifically Intosana, Sanatigh, Sanawarme and Caleosana, being plasters designed specifically for the healthiness of new buildings, existing buildings, works on green buildings and in the restoration of historic and monumental buildings. Untersana is composed of hydraulic lime, botticino, kaolin, calcium caseinate, Vichy salt, tartaric acid and natural fibres. Does not contain cements, resins, solvents, thinners and radioemissive aggregates. Anchoring scratch coat (applied by "spraying" or "splashing") for the formation of an adhesive bridge for easy grip of subsequent plasters, dehumidifying, breathable, based on hydraulic lime. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface". Pour about 2/3 of the mixing water into the mixer, add Untersana and the remaining water; continue to mix until a homogeneous lump-free mixture is obtained. The mixing water should be about 22-25% of the weight of the bag. After mixing is completed wait a few minutes before applying. "Spray" the product, with plastic fluid consistency, on the application supports, with plastering trowel and brick trowel or with plastering pump. Protect fresh surfaces from direct exposure to sunlight, from the rain and wind, cure the prolonged moist hardening. From 4 to 6 kg of Untersana per square metre of surface to be rendered. Bag 25 kg - Pallet: 50 x (Bag 25 kg)

Sanavel Breathable, natural, non-toxic, indoor paint, based on potassium silicate. Mineral-based, active formulation, high mildewcide and anti-condensation performance, prepared according to traditional recipes, for use in ecological building interventions, new buildings and in the restoration of vintage buildings and monuments. Sanavel consists of potassium silicate, natural pigments. It has very high breathability, remarkable mildewcide and antibacterial properties. It has no solvents, thinners, harmful substances and toxic emissions in general, and does not have thermoplastic effects. Restoring and decorative paint for interior environments. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc. Pre-existing paints (washable, organic, solvent based etc. ) must be thoroughly removed. Preliminarily treat the support with the fixative Sanaxil Fix. Apply by brush, roller or spray. Sanavel is "dust-free" (it has started to be consistent to the touch) after about 1 hour. It can be overcoated after 4-5 hours, while it will be dry in-depth after 10-12 hours. Apply from 0.30 to 0.40 liters of Sanavel per square metre of surface to be painted. Pail 4 l - Pail 14 l

Original Used Mobile Phone For Samsung 20FE 128GB Used Second Hand Mobile Phones US version Original Refuirbished, No any scratches, Like Brand New