Produkty dla płyta tnąca hdpe (2)

Repar Tix HG SB Thixotropic, structural, fibre reinforced cement mortar, with compensated shrinkage, with high intrinsic water tightness, and extraordinary physical and mechanical characteristics: adhesion, compression resistance, flexural strength, abrasion resistance, etc. Perfect for remediation of structural works and articles in degraded concrete and very high-performance coatings. Repar Tix HG SB, in addition to normal manual application techniques, it is a structural mortar specially formulated for applications with pumping/spray machines (wet spritz-beton technique). Particularly optimized parameters are: rheology, thixotropy and workability of the product, which allow spraying operations with reduced wear of the mechanical parts and little waste on the ground. Rheoplastic, thixotropic, structural, composite cement mortar, based on special cements and selected siliceous aggregates, reinforced with a balanced mixture of READYMESH polypropylene fibres and calcium metasilicate microfibres, added with specific agents and a high content of silica fume. After hardening, it provides very high performance in terms of intrinsic water tightness, resistance to washing and hydrolysing, mechanical strength, abrasion and cavitation, anti-carbonation, chemical-physical stability, resistance to harsh atmospheric agents and to leaching water. It has three-dimensional fibre-reinforcement, provides high hold; it is dimensionally stable (compensated shrinkage). The product can be supplied in mono-component or two-component version. The product, in the monocomponent version, is mixed with water (approx. 16% of the weight of the bag). In the two-component version, the product is mixed by adding the 4.5 kg of component B. The two-component version increases adhesion to the support and reduces free shrinkage to air, especially in the initial hardening phases and in particularly hot climates, without modifying the physical-mechanical characteristics of the end product. Repairs and protective coatings of hydraulic works (pipelines, dams, tunnels etc.), marine structures and artefacts in critical situations: aggressive chemical-physical agents, leaching water, marine atmosphere, etc. Specific for shotcrete interventions in galleries, tunnels, rock walls, irrigation and hydraulic channels, piles and micropiles, diaphragms, etc. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface". An adequate roughening of the surfaces by scarifying, sandblasting etc. is always necessary in order to obtain the maximum adhesion values to the substrate. The optimal values are obtained with high pressure hydro-scarification. Bare the irons undergoing disruptive oxidation or deeply oxidized, removing the rust of the exposed irons (by sandblasting or abrasive brushes). The use of pumping/spraying machines specifically designed to be used with fibre-reinforced structural mortars is recommended. For the spraying of structural mortars such as Repar Tix HG SB, an effective and sometimes prolonged mixing of the product, which must take place upstream of the pumping circuit, is always recommended. For this reason, the use of “plaster sprayers” with volumetric water dosage is not recommended. Pour about 2/3 of the mixing water into the mixer, add Repar Tix HG SB and the remaining water; continue to mix until a homogeneous lump-free mixture is obtained. The mixing water should be about 16% of the weight of the bag. Addition of Bond HG to the mixing water, (approx. 0.5 litres per 25kg bag of product) in the single component version, allows further improvement in terms of adhesion, hold, impermeability, workability, modelling and deformation capacity. In the case of use of the product in the two-component version, pour component B (liquid) into the mixer, gradually adding component A (powder) and mixing until the lumps are completely eliminated. For high coating thicknesses, static requirements, monolithic requirements, etc., performed with Repar Tix HG SB, it is advisable to use suitable metal reinforcements (electro-welded mesh, cages, etc.), anchored to the support with Syntech Profix, GROUT MICROJ, Repar Tix G2. Approximately 18,5 kg/m² of Repar Tix HG SB for every centimetre of thickness to be implemented (approximately 1850 kg per cubic metre). Bag 25 kg - Pallet: 50 x (Bag 25 kg)

Protech WAC-RC Single-component colored finish in water dispersion for the opaque protection of concrete surfaces and cementitious substrates, wall coverings, and appropriately prepared and primed floors. The product is a painting system suitable for environments with the presence of food, which can be used to protect walls and ceilings that comply with the HACCP protocol, in order to prevent possible food contamination. Excellent resistance to atmospheric agents and aggressive industrial environments Good water vapor permeability and water repellency Wide range of colors available Uniform matte finish Low maintenance over time Good resistance to diluted acids and alkalis, fuels and hydrocarbons Excellent resistance to detergents and disinfectants Excellent resistance to mold attack Perfectly washable It meets the following requirements: Legislative Decree n. 193 of 06/11/2007 “Implementation of Directive 2004/41/EC relating to food safety controls and application of community regulations in the same sector” - HACCP UNI 11021:2002 “Products and systems for painting environments with the presence of food”, in particular it is suitable for walls, ceilings and surfaces for which resistance to washing is required; can be washed with chloroactive detergent (detergent A); can be washed with alkaline degreaser (detergent B); can be washed with acid descaler (detergent C); can be washed with disinfectant (detergent D); resists temperature changes. Colored protective finish of concrete surfaces, cement plasters Anti-carbonation finishing of concrete structures Wall finishing for food, wine and butcher shops Wall finishing for chemical and pharmaceutical industries Finishing and coating of suitably prepared metal surfaces Protective finish for floors already treated with resins or primed Protective treatment of oxidized asphalt surfaces Finish for environments in the presence of food. Concrete The surfaces to be coated must be stable, clean and free of substances that can affect the adhesion of the coating such as dirt, grease, oil, traces of coatings and surface treatments, etc. Any weak or detaching parts must be removed before applying the product by mechanical sanding with diamond discs and dust extraction. The tensile strength must not be less than 1.5 N/mm². The application of Protech WAC-RC on new or particularly absorbent cementitious substrates must always be preceded by the application of a coat of Protech fix AC water-based anchoring primer. Wait 3-4 hours before applying the finish. Resin coatings The surfaces to be coated must be stable, clean and free of substances that can affect the adhesion of the coating such as dirt, grease, oil, etc. Sand the surface by mechanical sanding with diamond discs and dust extraction. It is advisable to wash the surfaces and wait for them to dry completely before applying the finish. The application of Protech WAC-RC on resinous and multilayer systems must always be preceded by sanding the entire surface in order to promote and guarantee optimal adhesion of the product to the support. PVC Wash the PVC surfaces to be treated with specific detergents to remove any substances that may affect the adhesion of the coating such as dirt, grease, oil, materials that block the pores in order to promote better capillary penetration of the product into the support. The application of Protech WAC-RC on PVC supports can be carried out directly with appropriate dilutions of the product in first and second coat. Steel Any welding residues must be removed and the joints sanded. Sandblast to cleanliness level Sa 2½ according to ISO8501-1. The surfaces to be coated must be free from dirt, oil, grease and impurities. Average surface roughness degree RZ ≥ 50 μm. An anti-corrosion treatment is recommended before applying the coating. The application of Protech WAC-RC on steel supports must always be preceded by the application of a coat of “surface tolerant” epoxy-polyamide primer in the solvent phase Syntech Poliurea Primer Epoxy Metal. Approximately 0.20 kg of Protech WAC-RC for each square meter of surface to be painted for each coat. Apply two coats.. Packaging: 20 kg bucket UM: €/kg