Produkty dla combi (4)

Elastotex 250 Combi Strap with high resilience and resistance, with an overall width of 25 cm, consisting of a special elastomeric layer in Hypalon, resistant to raging and wear and tear, for use in combination with the epoxy resins paste Syntech AS 21 or Syntech AS 31, for waterproofing watertight expansion joints in buildings, works and structures below the aquifer level or to ensure the water sealing of structural connections even off the ground. Specific applications for industrial or infrastructural use. The excellent adhesion with epoxy adhesives such as Syntech AS 21 (AS 31) is greatly improved thanks to the perforated edges that allow a collaboration between the lower layer and the upper layer of resin. SYNTECH AS epoxy fillers allow the gluing of the Elastotex 250 Combi strip on various types of substrates (see paragraph "Preparation of substrates") including pvc supports (see technical document "Adhesion test on pvc sheath"). The strip is flexible and deformable (even at low temperatures) and extremely resistant to traction, root aggression, atmospheric agents and many chemicals. It is easy to lay and this allows for quick, safe and non-hazardous applications for the applicator. Waterproofing expansion joints, including large ones, subject to considerable work movements, and of natural joints and fissures, also in conditions of hydraulic counter-thrust, in tunnels, silos, tanks, pools, basements, roofing, prefabricated coverings, road joints and hydraulic works in general. The concrete surfaces must certainly be free of incoherent parts, traces of grease, release agent, paints by sandblasting, shot peening, grinding or milling, followed by careful removal of dust. The cement conglomerates must have a minimum tensile strength of 1.5 N / mm2. The curing of the concrete must be at least 3 - 6 weeks depending on the climate. The metal surfaces must be perfectly clean and free from rust, calamine or lamination residues, by sandblasting or equivalent mechanical treatment followed by careful removal of dust (on metal surfaces pay maximum attention to the dew point). The polymeric surfaces must be roughened by sanding. Work areas, edges, etc. they must be delimited with adhesive tape. Mix the epoxy resin SYNTECH 21 (AS 31) thoroughly in the pre-determined amount as required (on average roughly 1 kg per meter). Spread the epoxy adhesive prepared as described above, on the sides of the joint to be waterproofed by toothed adhesive spreader, kept constantly clean, taking care to obtain uniformity of the thickness applied that must not be less than 2 mm. Unroll and apply the Elastotex 250 Combi strap, on the fresh adhesive spread, pressing it against the resin, stretching the ends by hand, taking care to avoid wrinkling and air bubbles, until the underlying resin leaks out from the holes on the strap. Apply with a metal filling knife a second layer (at least 2 mm) of Syntech AS 21 (AS 31) adhesive at the edges of the strap, already impregnated, in order to protect it permanently from accidental damage and to obtain certain monolithicity of the end to the support. For the joint between two adjacent straps, weld the end flaps for overlap and solder them using a special hot air welding machine. For additional security of the seal, a small layer of Syntech AS 21 (AS 31) should be applied on the heated flaps. The final system resistances will be reached after about 7 days after laying, but already after 24 hours at 20°C, values equal to 60-70% of the final performances can be obtained. In any case the performance after 24 hours will be much greater than those of a high quality concrete. 1 metre of Elastotex 250 Combi for each linear metre, being careful to overlap the rolls of approximately 5-10 cm in correspondence with the edges of the band to guarantee the permanent water tightness of the system. Consumption of epoxy resin for bonding about 1.5 kg / m. Roll 20 m

An accurate selection of high quality coffees from Central and South America, India and Africa roasted to perfection yields the De Roccis CREMOSO espresso. An extraordinary mild and smooth blend with a strong and yet delicate finish.

Elatotex 250 combi Strap with high resilience and resistance, with an overall width of 25 cm, consisting of a special elastomeric layer in Hypalon, resistant to raging and wear and tear, for use in combination with the epoxy resins paste Syntech AS 21 or Syntech AS 31, for waterproofing watertight expansion joints in buildings, works and structures below the aquifer level or to ensure the water sealing of structural connections even off the ground. Specific applications for industrial or infrastructural use. The excellent adhesion with epoxy adhesives such as Syntech AS 21 (AS 31) is greatly improved thanks to the perforated edges that allow a collaboration between the lower layer and the upper layer of resin. SYNTECH AS epoxy fillers allow the gluing of the Elastotex 250 Combi strip on various types of substrates (see paragraph "Preparation of substrates") including pvc supports (see technical document "Adhesion test on pvc sheath"). The strip is flexible and deformable (even at low temperatures) and extremely resistant to traction, root aggression, atmospheric agents and many chemicals. It is easy to lay and this allows for quick, safe and non-hazardous applications for the applicator. Waterproofing expansion joints, including large ones, subject to considerable work movements, and of natural joints and fissures, also in conditions of hydraulic counter-thrust, in tunnels, silos, tanks, pools, basements, roofing, prefabricated coverings, road joints and hydraulic works in general. The concrete surfaces must certainly be free of incoherent parts, traces of grease, release agent, paints by sandblasting, shot peening, grinding or milling, followed by careful removal of dust. The cement conglomerates must have a minimum tensile strength of 1.5 N / mm2. The curing of the concrete must be at least 3 - 6 weeks depending on the climate. The metal surfaces must be perfectly clean and free from rust, calamine or lamination residues, by sandblasting or equivalent mechanical treatment followed by careful removal of dust (on metal surfaces pay maximum attention to the dew point). The polymeric surfaces must be roughened by sanding. Work areas, edges, etc. they must be delimited with adhesive tape. Mix the epoxy resin SYNTECH 21 (AS 31) thoroughly in the pre-determined amount as required (on average roughly 1 kg per meter). Spread the epoxy adhesive prepared as described above, on the sides of the joint to be waterproofed by toothed adhesive spreader, kept constantly clean, taking care to obtain uniformity of the thickness applied that must not be less than 2 mm. Unroll and apply the Elastotex 250 Combi strap, on the fresh adhesive spread, pressing it against the resin, stretching the ends by hand, taking care to avoid wrinkling and air bubbles, until the underlying resin leaks out from the holes on the strap. Apply with a metal filling knife a second layer (at least 2 mm) of Syntech AS 21 (AS 31) adhesive at the edges of the strap, already impregnated, in order to protect it permanently from accidental damage and to obtain certain monolithicity of the end to the support. For the joint between two adjacent straps, weld the end flaps for overlap and solder them using a special hot air welding machine. For additional security of the seal, a small layer of Syntech AS 21 (AS 31) should be applied on the heated flaps. The final system resistances will be reached after about 7 days after laying, but already after 24 hours at 20°C, values equal to 60-70% of the final performances can be obtained. In any case the performance after 24 hours will be much greater than those of a high quality concrete. 1 metre of Elastotex 250 Combi for each linear metre, being careful to overlap the rolls of approximately 5-10 cm in correspondence with the edges of the band to guarantee the permanent water tightness of the system. Consumption of epoxy resin for bonding about 1.5 kg / m. Packaging: Roll of 20 meters Unit of Measure: €/m

Mildly sweet blend from the best Arabica and Robusta coffees with strong flavor and fragrance. It is indeed the traditional and quintessential Italian Espresso! Brazil : Smooth and well-balanced coffee with pure and fine aroma. A very aromatic blend with a chocolaty finish. Costa Rica : High quality coffee with a rich hazelnut colored crema and apple and date fragrance. Light acidity. Indonesia : Rich and fine Robusta coffee with a light caramel fragrance ideal even for the most demanding coffee connoisseurs. Full and strong flavor with a persistent finish. Vietnam : Full bodied Robusta, eclectic and distinctive. Colombia : All Columbian coffees are of the Arabica variety with a rich aromatic fragrance, slightly fruity and a wonderful hazelnut and flowery finish.This coffee is the result of the perfect combination of select Arabica and Robusta coffees. Creamy, smooth and velvety, unique and surprising with a sweet flavor and a fruity finish.