Produkty dla rury (3)

Beltseal Beltseal is a gasket “belt” produced with a special hydro-expansive rubber that reacts upon coming into contact with water that increases its initial volume. Thanks to its geometry, Beltseal is very quickly applied directly to PVC piping without additional processing. It hermetically seals any discontinuities that could easily be found in the concrete due to the presence of PVC conduit pipes. In many cases, such discontinuities could pass from one side of the masonry to the other and thus seriously compromise the waterproofing of the masonry itself. There are three sizes available which are respectively suitable for diameter pipes: 70/90 mm, 110/125 mm and 160/200 mm. The hydroexpansive capacity of Beltseal has been laboratory tested with two different types of water: demineralised and with a highly basic pH (to simulate conditions in contact with concrete). Expansion tests showed a respective change in volume of 300% and 250%. For underground concrete constructions with conduit pipes, where the wall is in direct contact with the ground and where there are no layers of waterproofing outside the masonry itself: basements, cellars, underground garages, below-ground and cellar environments, etcetera. Position the Beltseal hydrofoam gasket centrally in respect of the length of the pipe (using one gasket per pipe). No. 1 Beltseal gasket for each conduit pipe to be sealed. Packaging: Bulk from 1 piece Unit of Measure: €/piece

Supply of mineral-insulated heating cables for pipes, gutters, ramps, and industrial applications. Heating cables are among the most commonly used solutions for heating pipes and surfaces, both external and internal, protecting them from cold damage. The complete range of heating cables offered by ESAF is suitable for various applications, including industrial contexts, for electric tracing and heating of tanks and cisterns, as well as domestic settings, to prevent pipes, gutters, or ramps from freezing. Why Choose Esaf Heating Cables: • Operating temperature down to -60°C • Easy to install with various available accessories • Cables suitable for large-scale tracing SUPPLY OF HEATING CABLES FOR DOMESTIC AND INDUSTRIAL USE ESAF specialises in the supply and sale of high-performance electrical resistors for the temperature control sector. Looking for more information? Contact us to request the catalogue of heating cables provided and explore the various solutions. CATALOGUE OF SUPPLIED HEATING CABLES Esaf offers a wide range of heating cables to suit every type of application, both domestic and industrial: • Self-regulating heating cables • Constant power heating cables • Mineral-insulated heating cables • Frost protection cables for metal and plastic pipes • Heating cables for roofs and gutters • Heating mats and trace heaters for ramps • Heating cables for long pipes • Heating cables for industrial processes • Accessories for heating cables

Syntech StopAQ Mono-component Sealant compound, permanently plastic, slightly warm (+10% in volume in contact with water), for waterproofing underground holes, through which one or many wires and/or technical pipes pass, in masonry structures. It is extruded around the cables passing using specific dosing gun for 600 ml bags, and then covered with thixotropic mortar Repar Tix G2. - It does not harden over time, while maintaining its original plasticity. - It is a non-toxic material. - It is easy to apply, it adheres both to dry and wet surfaces. Usable even in the presence of slight water seepage. - It expands slightly in contact with water (+10% ), thereby sealing any losses that may arise due to subsidence or vibration. Waterproof sealing for drilled holes in walls of concrete, bricks, tufa, etc., which are crossed by passing electrical cables and/or technical tubes in general (gas, plumbing, etc.). Dust, soil, sand, loose parts, rust, and layers of paint of the pipes and old deteriorated sealant material must be removed with pressurised water or brushing, before applying the compound. The inner surface of the tube/hole containing the passing cables should be damp or wet. To limit the thickness of Syntech StopAQ, it is recommended to insert a barrier of polyethylene foam kerbs with an appropriate diameter (Filtene Fondogiunto). Syntech StopAQ will be extruded into the hole to be sealed, taking care that the paste encompasses all the passing cables. Compact, with the help of a wooden handle or the like, the paste just extruded against the polyethylene "barrier" previously positioned to seal all the gaps. The depth of clogging made with Syntech StopAQ must be at least 8-10 cm. Smooth the outer surface of Syntech StopAQ, with special spatula or gloved hand, compacting it well. Finally, close the "mouth" outside of the tube/hole with Repar Tix G2, minimum 2 cm thick, smoothing around the cables with a spatula. Approximately 1.7 cartridges of Syntech StopAQ for each cubic decimetre of volume to be filled. Cartridge 533 cc